KOS-L702
WIDE TOUCH SCREEN MONITOR 7 page 2-11
INSTRUCTION MANUAL
MONITEUR ECRAN LARGE TACTILE 7 page 12-21
MODE D’EMPLOI
WIDE TOUCH SCREEN MONITOR 7 Seite 22-31
BEDIENUNGSANLEITUNG
BREEDBEELD MONITOR MET AANRAAKSCHERM 7 blz 32-41
GEBRUIKSAANWIJZING
MISONTITORR UTOUZCHIOSCNREEINPPAENORRAMLIC’OU7SpaOgina 42-51
MONITOR DE PANTALLA TÁCTIL PANORÁMICA 7 página 52-61
MANUAL DE INSTRUCCIONES
MONITOR DE ECRÃ LARGO DE TOQUE 7 página 62-71
MANUAL DE INSTRUÇÕES
宽屏幕触控显示器 7 72-81页
使用说明书
Take the time to read through this instruction manual.
Familiarity with installation and operation procedures will help you obtain the best
performance from your new monitor.
For your records
Record the serial number, found on the back of the unit, in the spaces designated on the
warranty card, and in the space provided below. Refer to the model and serial numbers
whenever you call upon your Kenwood dealer for information or service on the product.
Model KOS-L702 Serial number
US Residence Only
Register Online
Register your Kenwood product at
© B64-3528-00/00 (WV)
Notes
• If you experience problems during installation,
consult your Kenwood dealer.
• When you purchase optional accessories, check
with your Kenwood dealer to make sure that they
work with your model and in your area.
Screen brightness during low
temperatures
When the temperature of the unit falls such as
during winter, the liquid crystal panel’s screen will
become darker than usual. Normal brightness will
return after using the monitor for a while.
• If the unit fails to operate properly, press the Reset
button.
A/V controller you can control from the
KOS-L702 (As of March, 2007):
KOS-V500, KOS-V1000
Reset button
• The illustrations of the display and the panel
appearing in this manual are examples used to
explain more clearly how the controls are used.
Therefore, what appears on the display in the
illustrations may differ from what appears on
the display on the actual equipment, and some
of the illustrations on the display may represent
something impossible in actual operation.
Information on Disposal of Old Electrical
and Electronic Equipment (applicable for
EU countries that have adopted separate
waste collection systems)
Products with the symbol (crossed-out
wheeled bin) cannot be disposed as
household waste.
Old electrical and electronic equipment
should be recycled at a facility capable
of handling these items and their
waste byproducts. Contact your local
authority for details in locating a
recycle facility nearest to you. Proper
recycling and waste disposal will help
conserve resources whilst preventing
detrimental effects on our health and the
environment.
Cleaning the Unit
If the faceplate of this unit is stained, wipe it with a
dry soft cloth such as a silicon cloth.
If the faceplate is stained badly, wipe the stain off
with a cloth moistened with neutral cleaner, then
wipe it again with a clean soft dry cloth.
¤
•
Applying spray cleaner directly to the unit may affect its
mechanical parts. Wiping the faceplate with a hard cloth
or using a volatile liquid such as thinner or alcohol may
scratch the surface or erases characters.
|
English
3
Operations
Auto Dimmer sensor
SRC/
PWR OFF
MODE
O
ꢀ
FUNC/
AV OUT
V.SEL/
V.OFF
Switches the audio source
Press the [SRC] button.
Each time the button is pressed, the audio source
is changed.
⁄
Controlling of optional A/V controllers is possible by
touching the screen of this unit.
Functions which can be controlled vary depending
on the A/V controllers. Refer to the instruction
manual of the connected A/V controller for more
information.
⁄
•
Refer to <Switches the audio source> of <Basic
Operations> of the A/V controller's manual.
Power
Switches the video source
Press the [V.SEL] button.
Turning ON the Power
Press the [SRC] button.
Each time the button is pressed, the video source
Turning OFF the Power
is changed.
Press the [SRC] button for at least 1 second.
⁄
•
Refer to <Switches the video source> of <Basic
Operations> of the A/V controller's manual.
Volume
Increasing Volume:
Press the [5] button.
Decreasing Volume:
Press the [∞] button.
|
4
English
Switching Screen Mode
Swithing the Display off mode
Press the [MODE] button.
You can set the display off mode for the monitor.
Each time the button is pressed, the screen
mode switches as follows:
Press the [V.SEL] button for at least 1 second.
Exit the Display off mode
Press any button.
Press the button other than the [5] and [∞]
buttons.
Display
Setting
"Full"
Full picture mode
"Zoom"
"Just"
Zoom picture mode
Justify picture mode
Normal picture mode
Switches AV OUT source
Selects an AV source to be output at the "AV
OUTPUT" terminals.
Press the [FUNC] button for at least 1 second.
Each time the button is pressed for at least 1
second, the AV output is changed.
"Normal"
⁄
•
Refer to <Switches AV OUT source> of <Basic
Operations> of the A/V controller's manual.
⁄
•
Refer to <Monitor Setup> of the A/V controller's
manual.
•
When you select the Menu, Easy Control screen,
or Navigation, the display is shown in the full-size
display mode automatically. The screen mode of these
displays cannot be changed.
Switches the function screen
Switches to the control screens such as Source
Control Screen.
Press the [FUNC] button.
Each time the button is pressed, the function
control screen is changed.
Setting
Picture & Easy Control Panel
Source Control Screen
Picture Panel (OFF)
⁄
•
Refer to <Switches the function screen> of <Basic
Operations> of the A/V controller's manual.
|
English
5
Accessories
1
5
6
7
..........1
..........1
..........5
..........1
..........1
..........1
..........1
2
3
4
(Ø4 × 12 mm)
|
6
English
Installation Procedure
1. To prevent short circuits, remove the key from
the ignition and disconnect the · terminal of
the battery.
2. Make the proper input and output cable
connections for each unit.
3. Connect the wiring harness connector to the
unit.
4. Install the unit in your car.
¤
•
If the fuse blows, first make sure that the wires have not
caused a short circuit, then replace the old fuse with one
with the same rating.
•
Do not let unconnected wires or terminals touch metal
on the car or anything else conducting electricity. To
prevent short circuits do not remove the caps from
unused terminals or from the ends of the unconnected
wires.
5. Reconnect the · terminal of the battery.
6. Press the reset button. (page 3)
•
•
•
After the unit is installed, check whether the brake lamps,
blinkers, wipers, etc. on the car are working properly.
Insulate unconnected wires with vinyl tape or other
similar material.
Thoroughly wipe away oil and other dirt from the
installation surface.
2 WARNING
•
•
•
To prevent shorting, disconnect the battery cable from
the negative terminal of the battery during installation.
Be sure to firmly stabilise this product. Do not install it in
a location which is not stable.
Follow the installation and wiring procedures described
in this manual. Improper wiring or modified installation
can not only result in malfunction or damage to the unit
but may also result in an accident.
Please avoid installation on uneven surfaces.
•
Do not install the unit in the following locations.
• A location which interferes with the operation of the air
bag system.
• A location which is not made of plastic.
\ Installing on leather, wood or cloth may damage the
surface.
• A location subject to direct sunlight, subject to the air
from the air conditioner, or subject to moisture or high
temperature.
\ This may cause deformation of the monitor unit.
If you are not going to install the unit using the supplied
monitor stand, be sure to use a commercially available
monitor stand. (Mounting holes for such a stand are
located on the bottom of the monitor unit.)
•
|
English
7
Connection
Monitor Unit
Accessory 1
A/V controller (Optional accessory)
(KOS-V500)
MONITER POWER
Connect the wiring harness
referring to the instruction
manual of the connected A/V
controller.
A/V controller (Optional accessory)
(KOS-V1000)
AV
IN
AV
OUT
MONITOR
POWER
MONITOR
I/F
POWER
2
2
1
PRE
OUT
FM/
AM
AV
IN
R-CAM
V-IN
1
AV
OUT
SUB
REAR FRONT
VIDEO
VVIIDDEEOO
MONITER POWER
Connect the wiring harness
referring to the instruction
manual of the connected A/V
controller.
|
8
English
Installation
Installation for Monitor Unit
5 Secure the stand using the supplied tapping
screw (Accessory 3).
Installation location and cleaning
6 After attaching the stand, allow it to sit
undisturbed for 24 hours. Take care not to apply
any force to the stand during this time.
Select for installation a location where the stand
can be placed completely horizontal or where the
front edge of the support (petal-shaped part) can
be attached horizontally as shown in Figure A.
7 Insert the shoe of the monitor unit into the
bracket (Accessory 2).
Do not install in locations where the entire support
is at a diagonal such as in Figure B or where the
monitor unit is facing down such as in Figure C.
¤
•
Insert the shoe into the bracket (Accessory 2) as far as it
goes. (Fig. 1)
B
8 Adjust the height, horizontal and vertical angle
of the monitor unit, and securely tighten the
installation screws using the supplied hexagon
wrench (Accessary 4).
A
C
You can also adjust the monitor unit's forward
position by loosening the angle adjustment
knobs and adjusting the angle of the monitor
unit's installation stand.
¤
•
Thoroughly wipe away and dust or grease from the
installation location using a cloth which has been soaked
in a neutral cleaning agent and wrung out. Attach the
stand after allowing the installation location to dry.
Installation for Monitor Unit
Fig. 1
1 Install the shoe on the rear of the TV monitor
temporarily using the supplied hexagon wrench
(Accessary 4).
Shoe
⁄
•
When adjusting the fixing screw of the shoe, use the
hexagon wrench (Accessary 4) that came with the
product. Using other hexagon wrenches may damage
the screw.
Accessory 4
2 Bend the stand support to conform to the shape
Accessory 2
of the installation location.
3 Adjust the shape of the support so that there is
no rattling or gap when the stand is placed on
the support.
Accessory 3
4 Peel off the protective strip from the double-
sided tape on the bottom of the stand and
securely attach the stand.
Tighten
Accessory 4
¤
Loosen
•
Do not attach the double-sided tape more than once or
touch the adhesive with your fingers as this will weaken
its adhesive strength.
Protective strip
•
If the temperature of the surface of the installation
location is low, warm it up using a heater or other means
before attaching the stand. Low temperature may
weaken the adhesive strength of the tape.
Installation surface
•
The supplied stand is specially intended for this product.
Do not use it with another monitor.
|
English
9
Installation
Installation for Monitor Unit (For Headrest)
Mounting and wiring this product requires skills and experience. For safety's sake, leave the mounting and
wiring work to professionals.
Before mounting the monitor to the headrest:
• Perform the required external connections first (Accessory 1).
• Using the supplied paper template (Accessory 7), mark the area to be cut out of the headrest, then
carefully cut it.
1 Connect Monitor and system cord (Accessory 1).
2 Install the monitor unit in the bracket (Accessory 5).
Headrest
Installation plate (not supplied)
Accessory 1
Accessory 5
Monitor Unit
Screws (not supplied)
Paper template (Accessory 7)
Accessory 1
Removing the Monitor Unit (For Headrest)
1 Insert the removal tool (Accessory 6) deeply into the slots on each side, as shown.
Accessory 6
2 Pull the monitor unit all the way out with your hands, being careful not to drop it.
|
10
English
Troubleshooting Guide
What might seem to be a malfunction in your unit
may just be the result of slight misoperation or
miswiring. Before calling service, first check the
following table for possible problems.
⁄
•
Refer to the instruction manual of the connected A/C
controller for troubleshooting on the operation.
? The power does not turn ON.
✔
The motor is not attached to the bracket securely.
☞
Attach the motor to the bracket until it clicks.
? Nothing happens when the buttons are pressed.
✔
The computer chip in the unit is not functioning
normally.
☞
Press the reset button on the unit (page 3).
Specifications
Specifications subject to change without notice.
Monitor Section
General
Screen size
Operating voltage
: 6.95 inches wide
: 14.4 V DC (11 - 16 V)
156.2(W) × 82.4(H) × 176.0(Diagonal) mm
6-1/8(W) × 3-1/4(H) inches
Display system
: Transparent TN LCD panel
Drive system
: TFT active matrix system
Number of pixels
: 336,960 pixels (480 H × 234 V × RGB)
Effective pixels
: 99.99%
Pixel arrangement
: RGB striped arrangement
Current consumption
: 1.5 A
Operational temperature range
: –10°C to +60°C
Storage temperature range
: –20°C to +85°C
Dimensions (W × H × D)
: 177 × 122 × 34 mm
7 × 4-6/8 × 1-5/16 inch
Weight
: 460 g (1.01 lbs)
Back lighting
: Cold cathode tube
Colour system
: NTSC/ PAL
Analog RGB input (13P)
: 0.7 Vp-p/ 75 Ω
Although the effective pixels for the liquid crystal panel is given as 99.99% or more, 0.01% of pixels may not light or may
light incorrectly.
|
English
11
|