Beko Clothes Dryer DC 7110 User Manual

Dryer  
DC 7110  
 
1 Important safety information  
This section includes safety information that will  
help protection from risks of personal injuries  
or materialistic damages. Failure to follow  
these instructions shall cause any warranty and  
reliability commitment to become void.  
that are contaminated or spotted with such  
materials should not be dried in the product  
since they emit flammable or explosive vapor.  
• Do not dry items cleaned with industrial  
chemicals in the dryer.  
• Do not dry unwashed items in the dryer.  
• Items soiled with cooking oils, acetone,  
alcohol, fuel oil, kerosene, stain remover,  
turpentine, paraffin and paraffin removers  
must be washed in hot water with plenty of  
detergent before being dried in the dryer.  
• Garments or pillows bolstered with rubber  
foam (latex foam), shower bonnets, water  
resistant textiles, materials with rubber  
reinforcement and rubber foam pads should  
not be dried in the dryer.  
General safety  
• Never place the machine on a carpet-covered  
floor, otherwise, lack of airflow beneath  
the machine may cause electrical parts to  
overheat. This will cause problems with your  
machine.  
• If the power cable or mains plug is damaged,  
you must call Authorised Service Agent for  
repair.  
• The product should not be plugged in during  
installation, maintenance and repair works.  
Such works should always be made by the  
technical service. Manufacturer shall not  
be held responsible for damages arising  
from processes carried out by unauthorised  
persons.  
• Connect the product to a grounded outlet  
protected by a fuse of suitable capacity as  
stated in the technical specifications table.  
• Operate your product at temperatures  
between +5°C and +35°C.  
• Do not use electrical devices in the product.  
• Do not connect the air exit of the product  
to the chimney holes which are used for the  
exhaust fumes of the devices operating with  
gas or other types of fuel.  
• Do not use fabric softeners and anti-static  
products unless they are recommended by  
the manufacturers of the fabric softener or  
the product.  
• This product must be grounded. Grounding  
installation decreases the risk of electric  
shock by opening a path with low resistance  
for the electricity flow in case of a malfunction  
or failure. Power cable of this product is  
equipped with a conductor and a grounding  
plug that allows for grounding the product.  
This plug must be installed appropriately and  
inserted into a socket which is grounded  
in accordance with the local laws and  
regulations.  
• Do not install the product behind a door with  
a lock, sliding door or a door that has a hinge  
against the hinge of the dryer.  
• Do not install or leave this product in  
places where it will be exposed to outdoor  
conditions.  
• Do not tamper with the controls.  
• Do not perform any repair or part replacing  
procedures on the product even if you know  
or have the ability to perform unless it is  
clearly suggested in the operating instructions  
or the published service manual.  
• Inside and exhaust duct of the product must  
be cleaned by the qualified service personnel  
periodically.  
• Wrong connection of grounding conductor  
of the product can cause electric shock. If  
you have any suspect about the grounding  
connection, have it checked by a qualified  
electrician, service representative or service  
personnel.  
You must provide enough ventilation in  
order to prevent gases exiting from devices  
operating with other types of fuels including  
the naked flame from accumulating in the  
room due to the back fire effect.  
• Always clean the lint filter before or after each  
loading.  
• Never operate your dryer without the lint filter  
installed.  
• Do not allow fibre, dust and dirt accumulation  
around the exhaust exit and at adjacent  
areas.  
• Power cable plug must be within easy reach  
after installation.  
• Do not use extension cords, multi-plugs  
or adaptors to connect the dryer to power  
supply in order to decrease the risk of electric  
shock.  
• Do not make any changes on the plug  
supplied with the product. If it is not  
compatible with the socket, have a qualified  
electrician change the socket with a suitable  
one.  
• Items cleaned or washed with gasoil/fuel oil,  
dry-laundry solvents and other combustible  
or explosive materials as well as the items  
• Do not reach into the machine when the  
drum is spinning.  
• Unplug the machine when it is not in use.  
• Never wash down the appliance with water!  
There is the risk of electric shock! Always  
 
3 EN  
disconnect by unplugging from the mains  
before cleaning.  
Children’s safety  
• Electrical appliances are dangerous for  
the children. Keep children away from the  
machine when it is operating. Do not let  
them tamper with the machine.  
• Never touch the plug with wet hands. Never  
unplug by pulling on the cable, always  
pull out by grabbing the plug only. Do not  
operate the machine if the power cable or  
plug is damaged!  
• Packaging materials are dangerous to  
children. Keep the packaging materials out  
of reach of children or dispose them by  
classifying according to waste directives.  
• Do not allow children sit/climb on or enter in  
the product.  
• Children should be supervised to ensure  
that they do not play with the product.  
• Close the loading door when you leave the  
area where the product is located.  
• Never attempt to repair the machine  
yourself, otherwise, you will be putting your  
life and others’ lives in danger.  
• For malfunctions that cannot be solved by  
following the information given in the safety  
instructions:  
Turn off the machine, turn off and contact an  
authorised service agent.  
• Do not stop the dryer before the drying  
cycle comes to an end unless you will  
remove all laundry from the dryer fast in  
order to lay them and dissipate the heat.  
• Remove the door of the drying compartment  
before decommissioning or disposing of the  
product.  
• The final step of the drying cycle (cool-  
down cycle) occurs without applying  
heat to ensure that the items are left at a  
temperature that will not damage them.  
• Fabric softeners or similar products should  
be used as specified by the fabric softener  
instructions.  
• Underwear that contains metal  
reinforcements should not be placed in  
a dryer. Damage to the dryer can result if  
metal reinforcements come loose during  
drying.  
• Check all garments for forgotten lighters,  
coins, metal pieces, needles, etc. before  
loading.  
• At times when your dryer is not in use or  
after the laundry is taken out following the  
completion of drying process, turn off by  
using the On/Off button. In cases when  
the On/Off button is on (while the dryer  
is energized), keep the door of the dryer  
closed.  
Intended use  
• This product has been designed for  
domestic use. It should not be used for  
other purposes.  
• Use the product only for drying laundry that  
are marked accordingly.  
• Dry only those articles in your product that  
are stated in this manual.  
• This product is not intended to be used by  
persons with physical, sensory or mental  
disorders or unlearned or inexperienced  
people (including children) unless they  
are attended by a person who will be  
responsible for their safety or who will  
instruct them accordingly for use of the  
product.  
 
4 EN  
2 Installation  
Refer to the nearest Authorised Service Agent  
for installation of your product.  
CPreparation of location and electrical  
installation for the product is under  
BcInussttaollmateiornsarensdpeolnescitbriiclitayl.connections must  
AbPeriocratrorieindsotaulltabtioyna, qviusaulaifilelydcpheercskonifntheel.  
product has any defects on it. If so, do not  
have it installed. Damaged products will  
cause risks for your safety.  
Appropriate installation location  
• Install the product in an environment which  
has no risk of freezing and is in a stable and  
level position.  
AMake sure that you have removed  
the transportation safety assembly  
(nylon+styrofoam pieces) before using the  
product for the first time. Do not leave any  
items inside the drum.  
• Operate your product in a well ventilated,  
dust-free environment.  
• Do not block the air ducts in front of and  
under the product with materials such as  
long pile rugs and wooden bands.  
• Do not place your product on a long pile rug  
or on similar surfaces.  
Under counter installation  
• Do not install the product behind a door with  
a lock, sliding door or a hinged door which  
can strike the product.  
• A special part (Part no. 297 360 0100)  
replacing the top trim must be provided and  
installed by the Authorised Service Agent in  
order to use the machine under a counter or  
in a cupboard. It should never be operated  
without the top trim.  
• Once the product is installed, it should stay  
at the same place where its connections  
have been made. When installing the  
product, make sure that the rear wall of it  
does not touch anywhere (tap, socket, etc.)  
and also pay attention to install the product  
• Leave at least 3 cm of space between  
the side and rear walls of the product and  
the walls of the counter/cupboard when  
installing your product under a counter or in  
a cupboard.  
Mounting over a washing machine  
• A fitting device should be used between  
the two machines when installing above a  
washing machine. The bracket (Part no. 297  
720 0200 white/297 720 0500 grey) must be  
installed by the Authorised Service Agent.  
• Place the product on a firm floor. If it will be  
placed on top of a washing machine, the  
approximate weight of both machines may  
reach 180 kg when they are full. Therefore,  
the floor must be capable of carrying the  
load on it!  
BaDt oa npolatcpelawcheetrheeitpwroildl sutcatyopnetrompaonfetnhtely.  
power cable.  
• Keep at least 1.5 cm distance to walls of  
other furniture.  
Removing the transportation safety  
assembly  
ARemove the transportation safety assembly  
before using the product for the first time.  
1. Open the loading door.  
2. There is a nylon bag inside the drum that  
contains a piece of styrofoam. Hold it from  
its section marked with XX.  
3. Pull the nylon towards yourself and remove  
the transportation safety assembly.  
Adjusting the feet  
In order to ensure that your machine operates  
more silently and vibration-free, it must stand  
level and balanced on its feet. Balance the  
machine by adjusting the feet.  
Rotate the feet to adjust until the machine  
stands level and firmly.  
 
5 EN  
accordance with recycled waste instructions.  
Do not dispose of them with normal domestic  
waste.  
Transportation of the machine  
1. Unplug the machine from the mains.  
2. Remove the water drain (if any) and  
chimney connections.  
3. Drain water remained in the machine  
completely before transportation.  
CNever unscrew the adjustable feet from their  
Disposing of the old machine  
Dispose of your old machine in an  
environmentally friendly manner.  
Refer to your local dealer or solid waste  
collection centre in your area to learn how to  
dispose of your machine.  
Before disposing of your old machine, cut off  
the power cable plug and make the loading  
door lock unusable to avoid dangerous  
conditions to children.  
housings.  
Electrical connection  
Connect the machine to a grounded outlet  
protected by a fuse of suitable capacity as  
stated in the technical specifications table. Our  
company shall not be liable for any damages  
that will arise when the machine is used on a  
circuit without grounding.  
• Connection must comply with national  
regulations.  
• If the current value of the fuse or breaker  
in the house is less than 13 Amps, have a  
qualified electrician install a 13 Amp fuse.  
• Power cable plug must be within easy reach  
after installation.  
• The voltage and allowed fuse or breaker  
protection are specified in the “Technical  
Specifications” section.  
• The specified voltage must be equal to your  
mains voltage.  
• Do not make connections via extension  
cables or multi-plugs.  
• The main fuse and switches must have a  
BcDoanmtaacgteddisptaonwceer ocfambleinimmuusmt o3nmlymbe. replaced  
BbIfythaeqpuraoldifiuecdteislefcaturilctyi,anit.must not be  
operated unless it is repaired! There is the risk  
of electric shock!  
First use  
To have the product ready for operation  
before calling the authorised service agent,  
make sure that its location and power supply  
installations are appropriate. If they are  
not, call a qualified electrician to have any  
necessary arrangements carried out.  
• Make sure that the power connections of  
the product are in accordance with the  
instructions given in relevant chapters of this  
manual.  
Disposing of packaging material  
Packaging materials are dangerous to children.  
Keep packaging materials in a safe place out  
of reach of children. Packaging materials of  
your product are manufactured from recyclable  
materials. Sort and dispose of them in  
 
6 EN  
Technical Specification  
EN  
2
Height (adjustable)  
84.6 cm  
59.5 cm  
53 cm  
7 kg  
Width  
Depth  
Capacity (max.)  
Weight (net)  
35 kg  
Voltage  
Rated power input  
Model code  
See type label  
Type label is located behind the loading door.  
 
7 EN  
3 Initial preparations for drying  
Things to be done for energy saving:  
• Make sure that you operate the product  
at its full capacity but pay attention to not  
exceeding it.  
• Spin your laundry at the highest speed  
possible when washing them. Thus,  
the drying time is shortened and energy  
consumption is decreased.  
• Pay attention to dry same types of laundry  
together.  
• Follow the instructions in the user manual for  
programme selection.  
• Make sure that sufficient clearance is  
provided at the front and rear side of the  
dryer for air circulation. Do not block the grill  
at the front side of the product.  
A B C D  
Low  
l n m  
o p q  
• Do not open the door of the machine during  
drying unless necessary. If you must certainly  
open the door, pay attention not to keep it  
open for a long time.  
• Do not add new (wet) laundry during drying.  
• Lint and fibres released from the laundry to  
the air during the drying cycle are collected in  
the “Lint Filter”. Make sure that you clean the  
filters before or after each drying.  
• In models with condenser, make sure that  
you clean the condenser regularly at least  
once every month or after every 30 drying  
cycles.  
• In vented models, follow the chimney  
connection rules in the user manual and pay  
attention to the chimney cleaning.  
• Ventilate the room, where the dryer is located,  
well during drying.  
• For power saving in models with lamps, at  
times when your dryer is not in use, keep the  
door closed if the On/Off button is pressed (if  
the dryer is energized).  
Laundry unsuitable for drying in the  
machine  
Laundry items with metal attachments such  
as belt buckles and metal buttons can  
damage your dryer.  
• Do not dry items such as woollens, silk  
garments and nylon stockings, delicate  
embroidered fabrics, laundry with metal  
accessories and items such as sleeping bags  
in the dryer.  
• Laundry made of delicate and valuable fabrics  
as well as lace curtains can be creased. Do  
not dry them in the dryer!  
• Do not dry items made of hermetic fibres  
such as pillows and quilts in the dryer.  
• Laundry made of foam or rubber will be  
deformed.  
Laundry suitable for drying in the  
• Do not dry laundry containing rubber in the  
dryer.  
machine  
CAlways follow the suggestions on the laundry  
labels. Dry only the laundry having a label  
stating that they are suitable for drying in  
a dryer and make sure that you select the  
appropriate programme.  
• Do not dry laundry exposed to petroleum, oil,  
combustible or explosive agents in the dryer  
even if they are washed beforehand.  
• Overly wet laundry or laundry with dripping  
water must not be put into the dryer.  
• Items cleaned or washed with gasoil/fuel oil,  
dry-laundry solvents and other combustible  
or explosive materials as well as the items  
that are contaminated or spotted with such  
materials should not be dried in the product  
since they emit flammable or explosive vapor.  
• Do not dry items cleaned with industrial  
chemicals in the dryer.  
• Do not dry your unwashed laundry in the  
dryer.  
• Items soiled with cooking oils, acetone,  
alcohol, fuel oil, kerosene, stain remover,  
 
8 EN  
turpentine, paraffin and paraffin removers  
must be washed in hot water with plenty of  
detergent before being dried in the dryer.  
degrade when the machine is overloaded.  
Furthermore, your dryer and your laundry  
• Garments or pillows bolstered with rubber CPcalancebeyoduarmlaaugneddr.y into the drum loosely so  
foam (latex foam), shower bonnets, water  
resistant textiles, materials with rubber  
reinforcement and rubber foam pads  
should not be dried in the dryer.  
that they will not get tangled.  
CLarge pieces (E.g.: bed sheets, quilt covers,  
large tablecloths) may bunch-up. Stop the  
dryer 1-2 times during drying process to  
separate bunched-up laundry.  
• Do not use fabric softeners and anti-static  
products unless they are recommended by  
the manufacturers of the fabric softener or  
the product.  
• Do not dry the underwear reinforced with  
metal parts in the dryer. If these metal  
reinforcements loosen and break during  
drying, they will damage your dryer.  
Preparing laundry for drying  
Check all laundry items before loading  
them into the product to make sure that  
there are no lighters, coins, metal items,  
needles and etc. in their pockets or on any  
part of them.  
• Fabric softeners and similar products must  
be used in accordance with the instructions  
of the manufacturer of the relevant  
products.  
• All laundry must be spun at the highest  
spin speed that your washing machine  
allows for the laundry type.  
• Laundry may be tangled after washing.  
Separate your laundry before placing them  
into your dryer.  
Following weights are given as examples.  
Approximate  
Home articles  
weights (g)  
Cotton quit covers (double) 1500  
Cotton quit covers (single)  
Bed sheets (double)  
Bed sheets (single)  
Large tablecloths  
Small tablecloths  
Tea napkins  
1000  
500  
350  
700  
250  
100  
700  
350  
Bath towels  
Hand towels  
Approximate  
weights (g)  
Garments  
Blouses  
150  
300  
200  
500  
350  
700  
100  
125  
Cotton shirts  
Shirts  
• Sort your laundry according to their types  
and thicknesses. Dry the same type of  
laundry together. E.g.: fine kitchen towels  
and table cloths dry faster than the thick  
bath towels.  
Cotton dresses  
Dresses  
Jeans  
Correct load capacity  
Handkerchiefs (10 pieces)  
T-Shirts  
Loading the laundry  
• Open the loading door.  
• Place laundry items loosely into the dryer.  
• Push the loading door to close. Ensure that  
no items are caught in the door.  
A
Consider the information in the  
"Programme Selection Table". Always start  
the programme in accordance with the  
CmAdadxiinmgulmaulnodardyctoapthaecitmy.achine more  
than the level shown in the figure is not  
recommended. Drying performance will  
 
9 EN  
4 Selecting a Programme and OperatingYour Machine  
Control panel  
4
1
2
3
7
6
5
1. Filter cleaning warning light  
4. On/Off button  
Warning light turns on when the filter is full.  
2. Program follow-up indicator  
Used to follow-up the progress of the current  
programme.  
Used to turn on and off the machine.  
5. Programme selection knob  
Used to select a programme.  
6. Start/Pause/Cancel button  
Used to start, pause or cancel the  
programme.  
3. Low temperature  
Used to dry in low temperatures.  
7. Water tank warning light  
Warning light turns on when the water tank is  
full.  
Low  
Cottons Synthetics  
temparature  
Ventilation  
Ready  
to iron  
Spin  
On/Off  
Ready to  
wear  
Filter  
cleaning  
Start Child-proof  
Timer  
follow-up  
indicator  
Tank  
full  
pause  
cancel  
lock  
 
10 EN  
Preparing the machine  
1. Plug in your machine.  
2. Place the laundry in the machine.  
3. Press the “On/Off” button.  
CPressing the “On/Off” button does not  
necessarily mean that the programme has  
started. Press “Start/Pause/Cancel” button  
of the machine to start the programme.  
Timer program selection  
Decide the appropriate time from the table  
below which includes drying temperature in  
degrees. Select the desired time with the timer  
program selection button.  
Dry at high temperature only  
for cotton laundry. Thick and  
multi layered laundry (E.g.:  
Extra dry  
towels, linens, jeans) are dried  
in a way that they do not  
require ironing before placing  
in the wardrobe.  
Normal laundry (E.g.:  
tablecloths, underwear) are  
Ready to  
dried in a way that they do not  
wear  
require ironing before placing  
in the drawers.  
Normal laundry (E.g., Shirts,  
dresses) are dried ready to be  
ironed.  
Iron Dry  
C For further program details, see, “Program  
Selection Table”  
Main programmes  
Anti-creasing  
A 2-hour anti creasing programme to prevent  
laundry from creasing will be activated if  
you do not take the laundry out after the  
programme is over. This programme rotates  
the laundry in 600-second intervals to prevent  
creasing.  
•Ventilation  
Only ventilation is performed for 10 minutes  
without blowing hot air. You can air your  
clothes that have been kept at closed  
environments for a long time thanks to this  
program to deodorize unpleasant odors.  
•Timer programs  
You can select one of the 20 min...105  
min...135 min... timer programs to achieve  
the final drying level. Dry the cotton laundry  
at high temperatures and synthetic and easy-  
care laundry at low temperatures depending  
on the type of the laundry.  
CYou must press the “Low temperature”  
button for synthetics  
 
11 EN  
Program selection and consumption table  
EN  
Program table  
Approximate  
amount of  
remaining  
humidity  
Spin speed in washing  
machine (rpm)  
Drying time  
(minutes)  
Programs  
Capacity (kg)  
Cottons / Coloreds  
1000  
800  
% 60  
% 70  
% 60  
% 70  
% 60  
% 70  
% 60  
% 70  
135  
150  
90  
7
Ready to Wear  
A
A
1000  
800  
3.5  
7
105  
105  
120  
60  
1000  
800  
Ready to Iron  
1000  
800  
3.5  
60-90  
Synthetics  
Ready to Wear  
800  
600  
% 40  
% 50  
60  
90  
B
3.5  
Energy consumption values  
Approximate  
amount of  
remaining  
humidity  
Energy  
Spin speed in washing  
machine (rpm)  
Programs  
Capacity (kg)  
consumption  
value kWh  
Cottons linen Ready to wear*  
Cottons Ready to iron  
7
7
1000  
1000  
% 60  
% 60  
4.48  
3.40  
Synthetics Ready to wear  
3.5  
800  
% 40  
1.60  
* : Energy Label standard program (EN 61121:2005)  
All values given in the table have been fixed according to EN 61121:2005 Standard. These  
values may deviate from the table according to the laundry type, laundry spin speed,  
environmental conditions and voltage fluctuations.  
 
12 EN  
Auxiliary function  
Adding/removing laundry in standby  
Low temperature  
mode  
This function allows for drying at lower  
temperatures and therefore saves energy.  
Warning LED will light up when you select the  
function.  
In order to add or take out laundry after the  
start-up of the program;  
1. Press the “Start/Pause/Cancel” button to  
switch the machine to “Pause” mode. Drying  
process will stop.  
2. Open the door at Pause position and close it  
again after adding or taking out laundry.  
3. Press “Start/Pause/Cancel” button to start the  
CpArongyralamun. dry added after the drying process  
was started may cause the already dried  
clothes in the machine intermingle with wet  
clothes and the result will be wet laundry after  
the drying process is over.  
CYou must use this function when you dry  
your synthetic or delicate laundry.  
Warning indicators  
CWarning indicators may differ according to the  
model of your dryer.  
Filter cleaning  
A warning light will turn on to remind filter  
cleaning after the programme finishes.  
CIf the filter cleaning warning light lights up  
continuously, please refer to, “Suggested  
solutions for problems”.  
Water tank  
Child-proof lock  
AWarning LED will light up at the end of the  
program or when the tank is full with water.  
The machine stops operating when this  
warning LED lights up during a program  
running. To restart the machine, please drain  
the water in the water tank. Press “Start/  
Pause/Cancel” button to start the program  
after you have emptied the water tank. The  
warning LED goes off and the program  
resumes operating.  
There is a childproof lock to prevent any  
program interruption due to the pressing of keys  
while the program is on. The loading door and  
all keys except the “On/Off” key on the panel are  
deactivated when the child-proof lock is active.  
In order to activate the childproof lock, press  
on the “Start/Pause/Cancel” and “Low  
temperature” buttons simultaneously for 3  
seconds.  
To start a new program after the program is  
over or to interrupt the program, the childproof  
lock should be deactivated. To deactivate the  
childproof lock, press the same buttons for 3  
sec.  
Starting the programme  
1. Press “Start/Pause/Cancel” button to start  
the programme.  
2. Light of the “Start/Pause/Cancel” button will  
turn on to indicate that the programme has  
started.  
Timer follow-up indicator  
One of the LEDs is on as far as program runs  
and shows the approximate remaining time.  
Changing the program after the  
program has started  
You can use this feature to dry your laundry in a  
different program after your machine has started  
to run.  
COne of the LEDs on the program follow-up  
For example;  
indicator starts flashing when the child-proof  
Press and hold the “Start/Pause/Cancel” button  
for about 3 seconds to select “90” minutes  
program instead of “60” minutes program.  
Select the “90” minutes program by rotating the  
program knob.  
Press “Start/Pause/Cancel” button to start the  
program.  
C The program which is selected first will  
go on even if the program selection button  
is moved and another program mode is  
selected while the machine is operating. You  
must cancel the ongoing program in order to  
change the drying program. (See, Ending the  
program through canceling)  
ClCochkildis-parcotoivfaltoecdk. is deactivated when the  
machine is restarted by pressing the On/Off  
button.  
Ending the program through canceling  
The program which is selected first will keep  
on going even if the position of the program  
selection button is changed. A new program  
can be selected and started after “Program  
cancel” is activated in order to change the drying  
program.  
To cancel any selected program;  
• Press “Start/Pause/Cancel” button for about  
a duration of 3 seconds. The “Filter cleaning”  
and “Water tank” warning LEDs as well as the  
 
13 EN  
“0” warning LED on the program follow-up  
indicator will light up at the end of this period  
for reminding purposes.  
AAs the inside of the machine will be  
excessively hot when you cancel the program  
while the machine is running, activate the  
ventilation program to cool it down.  
The machine will not start even if the “Start/  
Pause/Cancel” button is pressed, unless the  
program selection knob is returned to the  
initial program. The paused program must be  
cancelled in order to change the drying program.  
End of program  
The “Filter cleaning” and “Water tank” warning  
LEDs as well as the “0” warning LED on the  
program follow-up indicator will light up at the  
end of the program. The door can be opened  
and the machine becomes ready for a second  
cycle.  
Press the “On/Off” button to shut down the  
machine.  
CA 2-hour anti creasing program to prevent  
laundry from creasing will be activated if you  
do not take the laundry out after the program  
has come to an end.  
CClean the filter after each drying (please see,  
Filter cleaning).  
CDrain the water tank after each drying (please  
see, Water tank)  
 
14 EN  
5 Maintenance and cleaning  
*To drain the water tank:  
1-Carefully remove the water tank by opening  
the kick plate cover/pulling the drawer.  
Filter Cartridge / Door Inner Surface  
Lint and fibres released from the laundry to the  
air during the drying cycle are collected in the  
“Filter Cartridge”.  
2-Drain the water in the tank  
CSuch fibre and lint are generally formed  
CdAulwrianygswceleaarningthaenfdiltewraasnhdintgh.e inner surfaces  
CoYof uthceacnocvleeraanfttehreefailtcehr danrydinfgilteprroacreeassb.y  
vacuum cleaner.  
To clean the filter:  
1. Open the loading door.  
2. Remove the cover filter by pulling it up and  
open the filter.  
3-If there is lint accumulation in the funnel of the  
water tank, clean it under running water.  
4-Place the water tank into its seat.  
3. Clean lint, fibre, and cotton raveling by hand  
or with a soft piece of cloth.  
4. Close the filter and place it back into its  
seat.  
For the condenser;  
Hot and humid air in the condenser is cooled  
C Clogging may arise on the filter surface after with the cold air from the room. Thus, the humid  
using your machine for some time; if this  
occurs, wash the filter with water and dry it  
air circulating in your dryer is condensed and  
then pumped into the tank.  
CClean the condenser after every 30 drying  
cycles or once a month.  
CbCefloeraenutshiengenatgiraeinin.ner surface of the cover  
and door gasket.  
To clean the condenser:  
1. If a drying process has been carried out, open  
the door of the machine and wait until it cools  
down.  
Water tank;  
The moisture in the damp laundry is taken from  
the laundry and condens ed. Drain the water  
tank after each drying cycle or during drying  
when “Water tank” warning light turns on.  
ACondensed water is not drinkable!  
ANever take out the water tank when the  
programme is running!  
If you forget to drain the water tank, your dryer  
will stop during the following drying cycles  
when the water tank is full and the “Water  
tank” warning light will turn on. If this is the  
case, press the “Start/Pause/Cancel” button to  
resume the drying cycle after draining the water  
tank.  
 
15 EN  
2. Unlock the 2 condenser locks after opening  
5. Place the condenser in its housing. Fasten  
the 2 locks and make sure that they are  
seated securely.  
the kick plate.  
3. Pull out the condenser.  
6. Close the kick plate cover.  
4. Clean the condenser by applying  
pressurized water with a shower armature  
and wait until the water drains.  
 
16 EN  
6 Suggested solutions for problems  
Drying process takes too much time  
• Meshes of the filter may be clogged. Wash with water  
Laundry comes out wet at the end of drying.  
• Meshes of the filter may be clogged. Wash with water.  
• Excessive laundry might have been loaded in. Do not load the dryer in excess.  
Dryer does not switch on or the programme does not start. Dryer is not activated when set.  
• It might have not been plugged in. Make sure that the machine is plugged in.  
• The loading door may be ajar. Make sure that the loading door is properly closed.  
• Programme might have not been set or the «Start/Pause/Cancel» button might have not  
been pressed. Make sure that the programme has been set and it is not in “Pause” mode.  
• «Childproof lock» might have been activated. Deactivate the childproof lock.  
Programme has been interrupted without any cause.  
• The loading door may be ajar. Make sure that the loading door is properly closed.  
• Electricity may be cut off. Press «Start/Pause/Cancel» button to start the programme.  
• Water may be full. Drain the water in the tank.  
Laundry has shrunk, become felted or deteriorated.  
• A programme suitable for the laundry type might have not been used. Dry only the laundry  
which is suitable for drying in dryer after checking the labels on your clothes.  
• Select a programme with suitable low temperature for the laundry type to dry your clothes.  
Drum lightning does not come on. (For models with lamp)  
• Dryer might have not been started by using the «On/Off» button. Make sure that the dryer is  
on.  
• Bulb may have blown. Call the authorized service to replace the bulb.  
“0” LED flashes.  
• The 2-hour anti creasing programme to prevent laundry from creasing might have been  
activated. Turn off the dryer and take out the laundry.  
“0” LED is on.  
• Programme has come to an end. Turn off the dryer and take out the laundry.  
“Filter cleaning” LED is on.  
• Filter might have not been cleaned. Clean the cover filter.  
“Water comes out the cover”  
• Clean the entire inner surface of the cover and door gasket.  
“Cover opens spontaneously.”  
• Push it until you hear that it is closed.  
For products with a condenser:  
“Water tank” warning LED is on.  
• Water may be full. Drain the water in the tank.  
“Condenser cleaning” LED is on.  
• Condenser might have not been cleaned. Clean the filters in the condenser under the kick  
plate.  
ACall an authorized service if the problem persists.  
 
17 EN  
 
 
 

Abocom Digital Photo Frame DPF102 User Manual
Accton Technology Switch ES4512C User Manual
Airlink101 Switch ASW308 User Manual
Altec Lansing Portable Speaker 405A User Manual
American DJ Power Supply DP 20A User Manual
AOSafety Respiratory Product A1655 User Manual
ATO Speaker System SCM16A User Manual
Axis Communications Security Camera Q6034 User Manual
Banner Power Supply PSA 24 User Manual
BB Electronics Network Card 485T User Manual