Beko Clothes Dryer DCU 7230 User Manual

Condenser  
Sensor Dryer  
DCU 7230  
 
TABLE OF CONTENTS  
1 Your Dryer  
Overview .............................................4  
Technical Specifications.......................5  
Auxiliary function................................16  
Warning indicators.............................16  
Time delay.........................................16  
Starting the programme.....................16  
Progress of programme.....................16  
Changing the programme after it has  
started...............................................16  
Child-proof lock.................................17  
Finishing by cancelling the programme17  
End of programme ............................18  
4
2 Important safety information6  
General safety .....................................6  
Intended use .......................................7  
Childrens safety ..................................7  
3 Installation  
8
7 Maintenance and cleaning 19  
Appropriate installation location ...........8  
Removing the transportation safety  
Filter Cartridge / Door Inner Surface...19  
Sensor ..............................................19  
Water tank;........................................19  
For the condenser ............................20  
assembly.............................................8  
Under counter installation ....................8  
Mounting over a washing machine.......8  
Connection to water drain; ..................8  
Adjusting the feet.................................9  
First use ..............................................9  
Disposing of packaging material ..........9  
Transportation of the machine .............9  
Disposing of the old machine...............9  
8 Suggested solutions for  
problems  
22  
23  
9 Guarantee  
What is covered?...............................23  
What is not covered?.........................23  
Important notes.................................23  
4 Electrical Connection  
10  
Attention!...........................................10  
Electrical requirements.......................10  
Fitting a different plug .......................10  
Washer/dryer combination.................10  
10 Service  
24  
5 Initial preparations for drying11  
Things to be done for energy saving:.11  
Laundry suitable for drying in the  
machine ............................................11  
Laundry unsuitable for drying in the  
machine ............................................11  
Preparing laundry for drying...............12  
Correct load capacity ........................12  
6 Selecting a Programme and  
OperatingYour Machine  
13  
Control panel.....................................13  
Preparing the machine.......................14  
Programme selection.........................14  
Programme selection and consumption  
table..................................................15  
 
1 Your Dryer  
Overview  
7
1
6
5
2
4
3
1- Control panel  
2- Kick plate opening tab  
3-Adjustable feet  
4-Kick plate  
5- Rating plate  
6- Fluff filter  
7- Power cord  
Download from Www.Somanuals.c4om.EANll Manuals Search And Download.  
Technical Specifications  
EN  
2
Height (adjustable)  
Width  
84.6 cm  
59.5 cm  
53 cm  
7 kg  
Depth  
Capacity (max.)  
Weight (net)  
36 kg  
Voltage  
Rated power input  
Model code  
See type label  
Type label is located behind the loading door.  
Specifications of this appliance may change without notice to improve the quality of the  
product. Figures in this manual are schematic and may not match your product exactly.  
Values stated on the machine labels or in the documentation accompanying it are obtained  
in laboratory in accordance with the relevant standards. Depending on operational and  
environmental conditions of the appliance, values may vary.  
 
5 EN  
2 Important safety instructions  
This section includes safety information that  
will help protection from risks of personal  
injuries or materialistic damages. Failure  
to follow these instructions shall cause  
supplied with the product. If it is not  
compatible with the socket, have a  
qualified electrician change the socket  
with a suitable one.  
any warranty and reliability commitment to  
become void.  
Items cleaned or washed with gasoil/  
fuel oil, dry-laundry solvents and other  
combustible or explosive materials as  
well as the items that are contaminated  
or spotted with such materials should  
not be dried in the product since they  
emit flammable or explosive vapor.  
Do not dry items cleaned with industrial  
chemicals in the dryer.  
Do not dry unwashed items in the dryer.  
Items soiled with cooking oils, acetone,  
alcohol, fuel oil, kerosene, stain remover,  
turpentine, paraffin and paraffin removers  
must be washed in hot water with plenty  
of detergent before being dried in the  
dryer.  
Garments or pillows bolstered with  
rubber foam (latex foam), shower  
bonnets, water resistant textiles,  
materials with rubber reinforcement and  
rubber foam pads should not be dried in  
the dryer.  
Do not use fabric softeners and  
anti-static products unless they are  
recommended by the manufacturers of  
the fabric softener or the product.  
This product must be earthed.  
General safety  
Never place the machine on a carpet-  
covered floor, otherwise, lack of airflow  
beneath the machine may cause  
electrical parts to overheat. This will  
cause problems with your machine.  
If the power cable or mains plug is  
damaged, you must call Authorised  
Service Agent for repair.  
The product should not be plugged  
in during installation, maintenance  
and repair works. Such works should  
always be made by the technical  
service. Manufacturer shall not be held  
responsible for damages arising from  
processes carried out by unauthorised  
persons.  
Connect the product to a grounded  
outlet protected by a fuse of suitable  
capacity as stated in the technical  
specifications table.  
Operate your product at temperatures  
between +5°C and +35°C.  
Do not use electrical devices in the  
product.  
Grounding installation decreases the risk  
of electric shock by opening a path with  
low resistance for the electricity flow in  
case of a malfunction or failure. Power  
cable of this product is equipped with  
a conductor and a grounding plug that  
allows for grounding the product. This  
plug must be installed appropriately and  
inserted into a socket which is grounded  
in accordance with the local laws and  
regulations.  
Do not install the product behind a door  
with a lock, sliding door or a door that  
has a hinge against the hinge of the  
dryer.  
Do not install or leave this product  
in places where it will be exposed to  
outdoor conditions.  
Do not connect the air exit of the product  
to the exit ducts which are used for the  
exhaust fumes of the devices operating  
with gas or other types of fuel.  
You must provide enough ventilation  
in order to prevent gases exiting from  
devices operating with other types of  
fuels including the naked flame from  
accumulating in the room due to the  
back fire effect.  
Always clean the lint filter before or after  
each loading.  
Never operate your dryer without the lint  
filter installed.  
Do not allow fibre, dust and dirt  
accumulation around the exhaust exit  
and at adjacent areas.  
Power cable plug must be within easy  
reach after installation.  
Do not tamper with the controls.  
Do not perform any repair or part  
replacing procedures on the product  
even if you know or have the ability to  
perform unless it is clearly suggested  
in the operating instructions or the  
Do not use extension cords, multi-plugs  
or adaptors to connect the dryer to  
power supply in order to decrease the  
risk of electric shock.  
Do not make any changes on the plug  
Download from Www.Somanuals.c6om.EANll Manuals Search And Download.  
published service manual.  
when the On/Off button is on (while the  
dryer is energized), keep the door of the  
dryer closed.  
Inside and exhaust duct of the product  
must be cleaned by the qualified service  
personnel periodically.  
Intended use  
Wrong connection of grounding  
conductor of the product can cause  
electric shock. If you have any suspect  
about the grounding connection, have  
it checked by a qualified electrician,  
service representative or service  
personnel.  
Do not reach into the machine when the  
drum is spinning.  
Unplug the machine when it is not in  
use.  
This product has been designed for  
domestic use. It should not be used for  
other purposes.  
Use the product only for drying laundry  
that are marked accordingly.  
Dry only those articles in your product  
that are stated in this manual.  
This product is not intended to be  
used by persons with physical, sensory  
or mental disorders or unlearned or  
inexperienced people (including children)  
unless they are attended by a person  
who will be responsible for their safety  
or who will instruct them accordingly for  
use of the product.  
Never wash down the appliance with  
water! There is the risk of electric shock!  
Always disconnect by unplugging from  
the mains before cleaning.  
Never touch the plug with wet hands.  
Never unplug by pulling on the cable,  
always pull out by grabbing the plug  
only. Do not operate the machine if the  
power cable or plug is damaged!  
Never attempt to repair the machine  
yourself, otherwise, you will be putting  
your life and others’ lives in danger.  
For malfunctions that cannot be solved  
by following the information given in the  
safety instructions:  
Children’s safety  
Electrical appliances are dangerous for  
the children. Keep children away from  
the machine when it is operating. Do not  
let them tamper with the machine.  
Packaging materials are dangerous to  
children. Keep the packaging materials  
out of reach of children or dispose  
them by classifying according to waste  
directives.  
Do not allow children sit/climb on or  
enter in the product.  
Children should be supervised to ensure  
that they do not play with the product.  
Close the loading door when you leave  
the area where the product is located.  
Turn off the machine and contact an  
authorised service agent.  
Do not stop the dryer before the drying  
cycle comes to an end unless you will  
remove all laundry from the dryer fast in  
order to lay them and dissipate the heat.  
Remove the door of the drying  
compartment before decommissioning  
or disposing of the product.  
The final step of the drying cycle (cool-  
down cycle) occurs without applying  
heat to ensure that the items are left at a  
temperature that will not damage them.  
Fabric softeners or similar products  
should be used as specified by the fabric  
softener instructions.  
Underwear that contains metal  
reinforcements should not be placed in  
a dryer. Damage to the dryer can result if  
metal reinforcements come loose during  
drying.  
Check all garments for forgotten lighters,  
coins, metal pieces, needles, etc. before  
loading.  
At times when your dryer is not in use  
or after the laundry is taken out following  
the completion of drying process, turn  
off by using the On/Off button. In cases  
 
7 EN  
3 Installation  
APrior to installation, visually check if the  
product has any defects on it. If so, do not  
have it installed. Damaged products will  
cause risks for your safety.  
Appropriate installation location  
Install the product in an environment  
which has no risk of freezing and is in a  
stable and level position.  
Operate your product in a well ventilated,  
dust-free environment.  
Do not block the air ducts in front of and  
under the product with materials such as  
long pile rugs and wooden plinths.  
Do not place your product on a long pile  
rug or on similar surfaces.  
Do not install the product behind a door  
with a lock, sliding door or a hinged door  
which can strike the product.  
Once the product is installed, it should  
stay at the same place where its  
connections have been made. When  
installing the product, make sure that the  
rear wall of it does not touch anywhere  
(tap, socket, etc.) and also pay attention  
to install the product at a place where it  
will stay permanently.  
AMake sure that you have removed  
the transportation safety assembly  
(nylon+styrofoam pieces) before using  
the product for the first time. Do not  
leave any items inside the drum.  
Under counter installation  
A special part (Part no. 297 360 0100)  
replacing the top trim can be provided  
and installed by the Authorised Service  
Agent in order fit the machine under a  
low counter or in a cupboard. It should  
never be operated without the top trim.  
Leave at least 3 cm of space between  
the side and rear walls of the product  
and the walls of the counter/cupboard  
when installing your product under a  
counter or in a cupboard.  
BDo not place the product on top of the  
power cable.  
Keep at least 1.5 cm distance to walls of  
other furniture.  
Removing the transportation  
safety assembly  
ARemove the transportation safety  
assembly before using the product for  
the first time.  
Mounting over a washing  
machine  
A fitting device should be used between  
the two machines when installing above  
a washing machine. The bracket must  
be installed by the Authorised Service  
Agent.  
Place the product on a firm floor. If  
it will be placed on top of a washing  
machine, the approximate weight of  
both machines may reach 180 kg when  
they are full. Therefore, the floor must be  
capable of carrying the load on it!  
1. Open the loading door.  
2. There is a nylon bag inside the drum that  
contains a piece of styrofoam. Hold it  
from its section marked with XX.  
3. Pull the nylon towards yourself and  
remove the transportation safety  
assembly.  
Connection to water drain;  
In products equipped with a condenser unit  
the water accumulated during the drying  
cycle is collected in the water tank. You  
should drain the accumulated water after  
each drying cycle.  
You can directly send the accumulated water  
out through the water drain hose supplied  
Download from Www.Somanuals.c8om.EANll Manuals Search And Download.  
with the machine instead of periodically  
draining the water collected in the water tank.  
Please refer to the detailed instructions  
supplied with the accessories pack.  
Connecting the water drain hose;  
C Never unscrew the adjustable feet from  
their housings.  
First use  
To have the product ready for operation  
before calling the authorised service  
agent, make sure that its location  
and power supply installations are  
appropriate. If they are not, call a  
qualified electrician to have any  
necessary arrangements carried out.  
Make sure that the power connections of  
the product are in accordance with the  
instructions given in relevant chapters of  
this manual.  
1. Remove the hose on the machine by  
pulling it out from its end. Do not use  
any tools to take out the hose.  
Disposing of packaging material  
Packaging materials are dangerous to  
children. Keep packaging materials in a safe  
place out of reach of children. Packaging  
materials of your product are manufactured  
from recyclable materials. Sort and dispose  
of them in accordance with recycled waste  
instructions. Do not dispose of them with  
normal domestic waste.  
2. Connect the special drain hose supplied  
with the machine to the pipe fitting.  
3. The other end of the drain hose can be  
directly connected to the wastewater  
drain or to the washbasin. The fitting  
must always be secured in all types of  
connections. Your house may be flooded  
if the hose gets out of its housing during  
water discharge.  
Transportation of the machine  
1. Unplug the machine from the mains.  
2. Remove the water drain and vent  
connections (if any).  
Important:  
The hose should be attached to a height  
of maximum 100 cm.  
3. Drain water remaining in the machine  
completely before transportation.  
You must be careful not the pinch or  
bend the hose.  
Disposing of the old machine  
Dispose of your old machine in an  
environmentally friendly manner.  
Refer to your local dealer or solid waste  
collection centre in your area to learn how to  
dispose of your machine.  
Before disposing of your old machine, cut off  
the power cable plug and make the loading  
door lock unusable to avoid dangerous  
conditions to children.  
The end of the hose should not be bent,  
it should not be stepped on and it must  
not be folded between the drain and the  
machine.  
Adjusting the feet  
In order to ensure that your machine  
operates more silently and vibration-free, it  
must stand level and balanced on its feet.  
Balance the machine by adjusting the feet.  
Rotate the feet to adjust until the machine  
stands level and firmly.  
 
9 EN  
4 Electrical Connection  
A Undercounter installation without the  
top cover must only be carried out by an  
authorised agent.Risk of electric shock.  
A Important  
Make sure that you have an earthed  
power outlet socket rated at 13 amps  
(minimum).  
Attention!  
Fitting a different plug  
If you use your dryer as built-in,  
the socket must be reachable after  
installation, or a separate switch (which  
can disconnect the two poles) must  
be used in the installation. Check for  
suitability.  
As the colours of the wires in the mains  
lead of this appliance may not correspond  
with the coloured markings identifying the  
terminals on your plug, proceed as follows:  
1 Connect the green - yellow or green (earth)  
wire to the terminal in the plug marked ‘E’  
or with the symbol or coloured green and  
yellow or green.  
For a permanent connection, a master  
switch with at least 3mm contact  
clearance and minumum 13 A rating must  
be used.  
2 Connect the blue (neutral) wire to the  
terminal in the plug marked ‘N’ or coloured  
black.  
Electrical requirements  
Before you insert the plug into the wall  
socket make sure that the voltage and  
the frequency shown in the rating label  
corresponds to your electricity supply.  
We recommend that this appliance be  
connected to the mains supply via a  
suitable switched and fused socket in a  
readily accessible position.  
3 Connect the brown (live) wire to the  
terminal in the plug marked ‘Lor coloured  
red.  
With the alternative plugs a 13A fuse must  
be fitted either in the plug or adaptor or in  
the main fuse box. If in doubt contact a  
qualified electrician.  
Green and yellow  
or green  
Should the mains lead of the appliance  
become damaged or need replacing at  
any time, it must be replaced by a special  
purpose made mains lead which can only  
be obtained from a Authorised Service  
Agent.  
A Warning  
This appliance must be earthed  
If the fitted moulded plug is not suitable for  
your socket, then the plug should be cut off  
and an appropriate plug fitted.  
N
L
Blue or black  
Brown or red  
The moulded plug on this appliance  
incorporates a 13A fuse. Should the fuse  
need to be replaced an ASTA approved  
BS1362 fuse of the same rating must be  
used. Do not forget to refit the fuse cover.  
In the event of losing the fuse cover, the  
plug must not be used until a replacement  
fuse cover has been fitted. Colour of the  
replacement fuse cover must be the same  
colour as that visible on the pin face of the  
plug. Fuse covers are available from any  
good electrical store.  
Washer/dryer combination  
Do not stack washing machine on top of  
the tumble dryer. This would damage both  
appliances and guarantees would become  
void. It is also unsafe to stack an appliance  
on top of another without using a suitable  
and approved stacking kit obtained from the  
manufacturer of the appliances.  
In order to avoid hazards, damaged  
supply cord should be replaced by the  
manufacturer, its service agent or similarly  
qualified people.  
Built-under installation  
This appliance can be installed under a  
worktop.  
 
10 EN  
5 Initial preparations for drying  
Things to be done for energy  
saving:  
A B C D  
Make sure that you operate the product  
at its full capacity but pay attention to  
not exceeding it.  
Low  
Spin your laundry at the highest speed  
possible when washing them. Thus,  
the drying time is shortened and energy  
consumption is decreased.  
l n m  
o p q  
Pay attention to dry same types of  
laundry together.  
Follow the instructions in the user  
manual for programme selection.  
Make sure that sufficient clearance is  
provided at the front and rear side of the  
dryer for air circulation. Do not block the  
grill at the front side of the product.  
Do not open the door of the machine  
during drying unless necessary. If you  
must certainly open the door, pay  
attention not to keep it open for a long  
time.  
Do not add new (wet) laundry during  
drying.  
Lint and fibres released from the laundry  
to the air during the drying cycle are  
collected in the “Lint Filter”. Make sure  
that you clean the filters before or after  
each drying.  
Laundry unsuitable for drying in  
the machine  
Laundry items with metal attachments  
such as belt buckles and metal buttons  
can damage your dryer.  
Do not dry items such as woollens, silk  
garments and nylon stockings, delicate  
embroidered fabrics, laundry with metal  
accessories and items such as sleeping  
bags in the dryer.  
Laundry made of delicate and valuable  
fabrics as well as lace curtains can be  
creased. Do not dry them in the dryer!  
Do not dry items made of hermetic fibres  
such as pillows and quilts in the dryer.  
Laundry made of foam or rubber will be  
deformed.  
In models with condenser, make sure  
that you clean the condenser regularly at  
least once every month or after every 30  
drying cycles.  
In vented models, follow the hose  
connection rules in the user manual and  
pay attention to the hose cleaning.  
Ventilate the room, where the dryer is  
located, well during drying.  
For power saving in models with lamps,  
at times when your dryer is not in  
use, keep the door closed if the On/  
Off button is pressed (if the dryer is  
energized).  
Do not dry laundry containing rubber in  
the dryer.  
Do not dry laundry exposed to  
petroleum, oil, combustible or explosive  
agents in the dryer even if they are  
washed beforehand.  
Overly wet laundry or laundry with  
dripping water must not be put into the  
dryer.  
Laundry suitable for drying in  
Items cleaned or washed with gasoil/  
fuel oil, dry-laundry solvents and other  
combustible or explosive materials as  
well as the items that are contaminated  
or spotted with such materials should  
not be dried in the product since they  
emit flammable or explosive vapor.  
Do not dry items cleaned with industrial  
chemicals in the dryer.  
the machine  
C Always follow the suggestions on the  
laundry labels. Dry only the laundry  
having a label stating that they are  
suitable for drying in a dryer and make  
sure that you select the appropriate  
programme.  
 
11 EN  
Do not dry your unwashed laundry in the  
dryer.  
C Adding laundry to the machine more  
than the level shown in the figure is not  
recommended. Drying performance  
will degrade when the machine is  
Items soiled with cooking oils, acetone,  
alcohol, fuel oil, kerosene, stain remover,  
turpentine, paraffin and paraffin removers  
must be washed in hot water with plenty  
of detergent before being dried in the  
dryer.  
overloaded. Furthermore, your dryer and  
your laundry can be damaged.  
C Place your laundry into the drum loosely  
so that they will not get tangled.  
Following weights are given as examples.  
Garments or pillows bolstered with  
rubber foam (latex foam), shower  
bonnets, water resistant textiles,  
materials with rubber reinforcement and  
rubber foam pads should not be dried in  
the dryer.  
Do not use fabric softeners and  
anti-static products unless they are  
recommended by the manufacturers of  
the fabric softener or the product.  
Do not dry the underwear reinforced with  
metal parts in the dryer. If these metal  
reinforcements loosen and break during  
drying, they will damage your dryer.  
Approximate  
Home articles  
weights (g)  
Cotton quit covers (double)  
Cotton quit covers (single)  
Bed sheets (double)  
Bed sheets (single)  
Large tablecloths  
Small tablecloths  
Tea napkins  
1500  
1000  
500  
350  
700  
250  
100  
700  
350  
Bath towels  
Hand towels  
Preparing laundry for drying  
Check all laundry items before loading  
them into the product to make sure that  
there are no lighters, coins, metal items,  
needles and etc. in their pockets or on  
any part of them.  
Fabric softeners and similar products  
must be used in accordance with the  
instructions of the manufacturer of the  
relevant products.  
All laundry must be spun at the highest  
spin speed that your washing machine  
allows for the laundry type.  
Laundry may be tangled after washing.  
Separate your laundry before placing  
them into your dryer.  
Sort your laundry according to their  
types and thicknesses. Dry the same  
type of laundry together. E.g.: fine  
kitchen towels and table cloths dry faster  
than the thick bath towels.  
Approximate  
weights (g)  
Garments  
Blouses  
Cotton shirts  
Shirts  
Cotton dresses  
Dresses  
Jeans  
150  
300  
200  
500  
350  
700  
100  
125  
Handkerchiefs (10 pieces)  
T-Shirts  
Loading  
Open the loading door.  
Place laundry items loosely into the  
dryer.  
Push the loading door to close. Ensure  
that no items are caught in the door.  
Correct load capacity  
AConsider the information in the  
“Programme Selection Table”. Always  
start the programme in accordance with  
the maximum load capacity.  
 
12 EN  
6 Selecting a Programme and OperatingYour Machine  
Control panel  
4
1
2
3
8
7
6
5
1. Filter cleaning warning light  
5. Programme selection knob  
Used to select a programme.  
6. Start/Pause/Cancel button  
Warning light turns on when the filter is  
full.  
2. Programme follow-up indicator  
Used to follow-up the progress of the  
current programme.  
Used to start, pause or cancel the  
programme.  
7. Water tank warning light*  
Warning light turns on when the water  
tank is full.  
3. Cancel audio warning  
Used to cancel the audio warning given  
at the end of the programme.  
4. On/Off button  
8.Time delay selection button*  
Used to set the time delay.  
* It may change according to the  
specifications of your dryer  
Used to turn on and off the machine.  
 
13 EN  
laundry from creasing will be activated if  
you do not take the laundry out after the  
programme is over. This programme rotates  
the laundry in 10-minute intervals to prevent  
creasing.  
Preparing the machine  
1. Plug in your machine.  
2. Place the laundry in the machine.  
3. Press the “On/Off” button.  
C PnerecsessisnagritlhyemeOann/Othfaftbthuettopnrodgoraems mnoet  
Special programmes  
For special cases, there are also extra  
programmes available:  
has started. Press "Start/Pause/Cancel"  
button of the machine to start the  
programme.  
C Additional programmes may differ  
according to the model of your machine.  
•Xpress 35’ min.  
Programme selection  
Decide the appropriate programme from  
the table below which includes drying  
temperatures in degrees. Select the desired  
programme with the programme selection  
button.  
You can use this programme to dry the  
cottons that are spun at high speeds in  
your washing machine. It can dry your 2 kg  
Cotton laundry (3 Shirts / 5 T-Shirts) within 35  
minutes.  
Dry at high temperature only for  
cotton laundry. Thick and multi  
layered laundry (E.g.: towels,  
linens, jeans) are dried in a way  
that they do not require ironing  
before placing in the wardrobe.  
CIn order to obtain better results from the  
dryer programmes, your laundry must  
be washed with suitable programme and  
spun at the recommended spin speeds  
in your washing machine.  
Extra dry  
•Shirt  
Normal laundry (E.g.:  
tablecloths, underwear) are  
Cupboard dry dried in a way that they do not  
require ironing before placing in  
the drawers.  
Dries the shirts in a more sensitive way so  
that they are less creased and ironed easily.  
CShirts may contain little amount of  
dampness at the and of the programme.  
It is advised not to leave the shirts in the  
dryer.  
Normal laundry (E.g.:  
tablecloths, underwear) are  
dried in a way that they do not  
require ironing before placing  
in the drawers, but more  
than those in the ready to  
wearoption.  
•Jeans  
You can use this programme to dry the jeans  
that are spun at high speeds in your washing  
machine.  
Normal dry  
CReview the relevant part of the  
programme table.  
Normal laundry (E.g., Shirts,  
dresses) are dried ready to be  
ironed.  
•Delicates  
Iron Dry  
You can dry at a lower temperature your very  
delicate laundry (silk blouses, fine underwear,  
etc.) that are suitable for drying or laundry  
which is advised to be hand-washed.  
C It is recommended to use a cloth bag  
to avoid certain delicate garments  
and laundry from getting creased  
or damaged. Take your garments  
immediately out of the dryer and hang  
them after the programme ends in order  
to prevent them being creased.  
•Freshen Up  
.
C FPoror gfurratmhemr eprSoeglreacmtiomneTdaebtlaeils, see,  
Main programmes  
Depending on the type of laundry, the  
following main programmes are available:  
•Cottons  
You can dry your durable laundry with this  
programme. Dries at high temperature. It  
is recommended to use for your cotton  
items (such as bed sheets, quilt cover,  
underclothing, etc.).  
Only ventilation is performed for 10 minutes  
without blowing hot air. You can air your  
clothes that have been kept at closed  
environments for a long time thanks to this  
programme to deodorize unpleasant odours.  
•Timer programmes  
Synthetics  
You can dry your less durable laundry  
with this programme. It dries at a lower  
temperature compared to the cottons  
programme. It is recommended for your  
synthetic laundry (such as shirts, blouses,  
synthetic/cotton blended laundry, etc.).  
C Do not dry curtains and lace in your  
machine.  
You can select one of the 10 min., 20 min.,  
40 min. and 60 min. timer programmes  
to achieve the desired final drying level at  
low temperatures. Programme dries at  
the selected time regardless of the drying  
temperature.  
Anti-creasing  
A 2-hour anti creasing programme to prevent  
 
14 EN  
Programme selection and consumption table  
EN  
Approximate  
amount of  
remaining  
humidity  
Spin speed  
Drying time  
(minutes)  
Programmes  
Capacity (kg)  
in washing  
machine (rpm)  
Cottons / Coloreds  
Cupboard dry  
7
7
1000  
1000  
60 %  
60 %  
114  
119  
A
A
Normal dry  
Iron dry  
7
1000  
60 %  
90  
A
Xpress 35 min.  
Shirt  
2
1.5  
4
1200-1400  
1000  
50 %  
50 %  
50 %  
35  
40  
80  
Jeans  
1000  
Synthetics  
Cupboard dry  
Cupboard dry  
3.5  
800  
800  
40 %  
40 %  
48  
40  
B
Delicates  
1.75  
B
Energy consumption values  
Approximate  
amount of  
remaining  
humidity  
Spin speed  
in washing  
machine (rpm)  
Energy  
consumption  
value kWh  
Programmes  
Capacity (kg)  
Cottons linen Ready to wear*  
Cottons Ready to iron  
7
7
1000  
1000  
800  
60 %  
60 %  
40 %  
3.92  
3.25  
1.42  
3.5  
Synthetics Ready to wear  
* : Energy Label standard programme (EN 61121:2005)  
All values given in the table have been fixed according to EN 61121:2005 Standard. These  
values may deviate from the table according to the laundry type, laundry spin speed,  
environmental conditions and voltage fluctuations.  
 
15 EN  
Auxiliary function  
C During the time delay period, laundry  
is rotated for 4 seconds in every 10  
minutes to prevent creasing.  
Cancel audio warning  
Your dryer will give an audio warning when  
the programme comes to an end. If you do  
not want to hear the audio warning, press  
“Cancel Audio Warning” button. The relevant  
light will turn on when this button is pressed  
and an audio warning will not be given when  
the programme comes to an end.  
Cancelling the time delay  
If you want to cancel the time delay  
countdown and start the programme:  
1. Press “Start/Pause/Cancel” button for  
about 3 seconds.  
2. Press “Start/Pause/Cancel” button to  
C You can select this function either before  
start the programme right away.  
or after the programme starts.  
Starting the programme  
1. Press “Start/Pause/Cancel” button to  
start the programme.  
2. Light of the “Start/Pause/Cancel”  
button will turn on to indicate that the  
programme has started.  
Warning indicators  
C Warning indicators may differ according  
to the model of your dryer.  
Filter cleaning  
A warning light will turn on to remind filter  
cleaning after the programme finishes.  
C If the filter cleaning warning light lights up  
continuously, please refer to, “Suggested  
solutions for problems”.  
Progress of programme  
Progress of a running programme is shown  
through the programme follow-up indicator.  
At the beginning of every programme step,  
the relevant indicator LED will light up and  
light of the completed step will turn off.  
“Drying”:  
Water tank  
Warning light starts flashing when the tank is  
filled with water. The dryer stops operating if  
the warning light turns on when a programme  
is running. Drain the water in the water tank  
to restart the dryer. Press “Start/Pause/  
Cancel” button to start the programme  
after you have emptied the water tank. The  
warning light turns off and the programme  
resumes operating.  
- Drying level will be illuminated during the  
whole drying process until the drying degree  
reaches “iron dry”.  
“Iron Dry”:  
- Starts to illuminate when the drying  
degree reaches “iron dry” step and remains  
illuminated until the next step.  
Time delay  
“Cupboard dry”:  
If you wish to dry your clothes at a later time,  
thanks to the time delay function, you can  
delay the programme start up to 3 hours, 6  
hours or 9 hours.  
Starts to illuminate when the drying degree  
reaches “Ready to wear” step and remains  
illuminated until the next step.  
“Final / Anti-creasing”:  
1. Open the loading door and put the  
laundry in.  
C Make sure that all air outlets are open,  
door filter is cleaned and the water tank  
is empty.  
2. Set the drying programme and, if  
required, the auxiliary functions.  
3. When the time programming button is  
pressed once, a 3 hour delay is selected  
and the relevant led lights. When the  
same button is pressed again, 6 hours;  
and if pressed once more, 9 hours delay  
will be selected. If the time programming  
button is pressed one more time, time  
delaying function will be cancelled. Set  
the time delay as you require.  
- Illuminates when the programme comes  
to an end and anti-creasing function is  
activated.  
CIf more than one LED light up or  
flash concurrently, it means there is  
malfunctioning or a failure (please see,  
Solution suggestions for problems).  
Changing the programme after it  
has started  
You can use this feature to dry your clothes  
under higher or lower temperatures after your  
dryer has started.  
For example;  
1. Press and hold the “Start/Pause/Cancel”  
button for about 3 seconds to “Cancel”  
the programme in order to select “Extra  
Dry” programme instead of “Iron Dry”  
programme.  
4. Delayed operation of the selected  
programme is started by pressing  
the "Start/Pause/Cancel" button after  
selecting the time delay.  
C Additional laundry may be loaded / taken  
out during the time delay period.  
2. Select the “Extra Dry” programme by  
rotating the programme selection button.  
 
16 EN  
3. Press “Start/Pause/Cancel” button to  
start the programme.  
audio warning” buttons simultaneously for 3  
seconds to activate the child-press lock.  
To start a new programme after the programme  
is over or to interrupt the programme, the child-  
proof lock should be deactivated. Press the same  
buttons for 3 sec. again to deactivate the child-  
proof lock.  
C Press “Start/Pause/Cancel” button for  
3 seconds to cancel the programme  
or turn the programme selection knob  
in any direction to end the programme  
while the machine is running. Water tank  
and filter cleaning warning lights turn on  
to warn the user when the programme is  
cancelled by pressing the “Start/Pause/  
Cancel” button for 3 seconds. However,  
the warning lights do not turn on when  
the programme is cancelled by turning  
the programme selection knob. Only the  
drying light turns on and the machine  
remains in hold until a new programme  
is selected and the “Start/Pause/Cancel”  
button is pressed. Child-proof lock of the  
machine should not be active in order  
to perform these two operations. If the  
child-proof lock is active, deactivate it  
before performing these operations.  
C Child-proof lock is deactivated when the  
machine is restarted by pressing the On/  
Off button.  
C Press the relevant buttons for 3 seconds  
to activate the child-proof lock. A long  
beep will be heard and the child-proof  
lock will be activated. A double beep  
will be heard if you press any button  
or turn the programme selection knob  
while the child-proof lock is active. Press  
the buttons for 3 seconds to deactivate  
the child-proof lock. Single beep will  
be heard and child-proof lock will be  
Adding/removing laundry in standby  
mode  
In order to add or remove laundry after the  
programme starts:  
1. Press the “Start/Pause/Cancel” button  
to switch the dryer to “Pause” mode.  
Drying process will stop.  
2. Open the door at “Pause” position and  
close it again after adding or taking out  
laundry.  
deactivated.  
AA double beep will be heard if you turn  
the programme selection knob when  
the machine is running and the child-  
proof lock is active. If you deactivate  
the child-proof lock without returning  
the programme selection knob to its  
previous position, the programme will  
be terminated since the position of the  
programme selection knob is changed.  
The drying light turns on and the  
machine remains on hold until a new  
programme is selected and the “Start/  
Pause/Cancel” button is pressed.  
3. Press “Start/Pause/Cancel” button to  
start the programme.  
C Any laundry added after the drying  
process has started may cause the dried  
clothes in the machine intermingle with  
wet clothes and the result will be wet  
laundry after the drying process is over.  
C Laundry may be added or taken out  
as much as desired during a drying  
process, but this process will extend  
the programme duration and increase  
energy consumption since the drying will  
be interrupted continuously. Therefore, it  
is recommended to add laundry before  
the drying programme has started.  
Finishing by cancelling the  
programme  
To cancel any selected programme:  
Press “Start/Pause/Cancel” button for about  
3 seconds. The “Filter cleaning”, “Water tank”  
and “End/ Anti-creasing” warning lights will  
turn on at the end of this period for reminding  
purposes.  
Child-proof lock  
There is a child-proof lock to prevent any  
programme interruption due to the pressing  
of button while the programme is running.  
The loading door and all buttons except  
the “On/Off” button on the control panel  
are deactivated when the child-proof lock is  
active.  
AAs the inside of the dryer will be  
excessively hot when you cancel the  
programme while the dryer is running,  
activate the ventilation programme to  
cool it down.  
Press the “Start/Pause/Cancel” and “Cancel  
 
17 EN  
End of programme  
The “End/Anti-creasing”, “Filter cleaning”  
and “Water tank” warning lights on the  
programme follow up indicator will turn on  
when the programme comes to an end.  
The door can be opened and the machine  
becomes ready for a second cycle.  
Press “On/Off” button to turn off the dryer.  
C Final step of the drying cycle (cooling  
step) is performed without heat  
application in order to keep the items  
at a temperature that would not harm  
them.  
C A 2-hour anti creasing programme to  
prevent laundry from creasing will be  
activated if you do not take the laundry  
out after the programme has come to an  
end.  
C If you will not take the laundry out  
immediately, do not stop the dryer before  
the drying process is complete.  
C Clean the filter after each drying (please  
see, Filter cleaning).  
C Drain the water tank after each drying  
(please see, Water tank)  
 
18 EN  
7 Maintenance and cleaning  
Filter Cartridge / Door Inner  
Surface  
Lint and fibres released from the laundry to  
the air during the drying cycle are collected in  
the “Filter Cartridge”.  
CSuch fibre and lint are generally formed  
during wearing and washing.  
C Always clean the filter and the inner  
surfaces of the cover after each drying  
process.  
Sensor  
C You can clean the filter and filter area by  
vacuum cleaner.  
To clean the filter:  
1. Open the loading door.  
2. Remove the cover filter by pulling it up  
and open the filter.  
3. Clean lint, fibre, and cotton by unravelling  
by hand or with a soft piece of cloth.  
4. Close the filter and place it back into its  
seat.  
C Clogging may arise on the filter surface  
after using your machine for some time;  
if this occurs, wash the filter with water  
and dry it before using again.  
There are humidity sensors in your dryer that  
detect whether the laundry is dry or not.  
To clean the sensor:  
1. Open the loading door of the dryer.  
2. Allow the machine to cool down if drying  
has been carried out.  
3. Wipe the metal sensors with a soft cloth,  
dampened with vinegar and dry them.  
C Clean metal sensors 4 times a year.  
ANever use solvents, cleaning agents  
or similar substances when cleaning  
since these materials can cause fire and  
explosion!  
Water tank;  
The moisture in the damp laundry is taken  
from the laundry and condensed. Drain the  
water tank after each drying cycle or during  
drying when “Water tank” warning light turns  
on.  
ACondensed water is not drinkable!  
ANever take out the water tank when the  
C Clean the entire inner surface of the  
door and door gasket by wiping with a  
damp cloth.  
 
19 EN  
programme is running!  
2. Unlock the 2 condenser locks after  
If you forget to drain the water tank, your  
dryer will stop during the following drying  
cycles when the water tank is full and the  
“Water tank” warning light will turn on. If  
this is the case, press the “Start/Pause/  
Cancel” button to resume the drying  
cycle after draining the water tank.  
To drain the water tank:  
opening the kick plate.  
1. Drain the water as shown on the  
picturre .  
3. Pull out the condenser.  
2. If there is lint accumulation in the water  
tank cover, clean it and press to close.  
4. Clean the condenser by applying  
pressurized water with a shower head  
and wait until the water drains.  
3. Place the water tank into its seat.  
For the condenser  
Hot and humid air in the condenser is  
cooled with the cold air from the room. Thus,  
the humid air circulating in your dryer is  
condensed and then pumped into the tank.  
C Clean the condenser after every 30  
drying cycles or once a month.  
To clean the condenser:  
1. If a drying process has been carried out,  
open the door of the machine and wait  
until it cools down.  
 
20 EN  
5. Place the condenser in its housing.  
Fasten the 2 locks and make sure that  
they are seated securely.  
6. Close the kick plate cover.  
 
21 EN  
8 Suggested solutions for problems  
Drying process takes too much time  
Meshes of the filter may be clogged. Wash with water  
Laundry comes out wet at the end of drying.  
Meshes of the filter may be clogged. Wash with water.  
Excessive laundry might have been loaded in. Do not load the dryer in excess.  
Dryer does not switch on or the programme does not start. Dryer is not activated when  
set.  
It might have not been plugged in. Make sure that the machine is plugged in.  
The loading door may be ajar. Make sure that the loading door is properly closed.  
Programme might have not been set or the «Start/Pause/Cancel» button might have  
not been pressed. Make sure that the programme has been set and it is not in “Pause”  
mode.  
«Childproof lock» might have been activated. Deactivate the childproof lock.  
Programme has been interrupted without any cause.  
The loading door may be ajar. Make sure that the loading door is properly closed.  
Electricity may be cut off. Press «Start/Pause/Cancel» button to start the programme.  
Make sure that the condenser cover and the red lock is closed securely.  
Laundry has shrunk, become felted or deteriorated.  
A programme suitable for the laundry type might have not been used. Dry only the  
laundry which is suitable for drying in dryer after checking the labels on your clothes.  
Select a programme with suitable low temperature for the laundry type to dry your  
clothes.  
Drum lightning does not come on. (For models with lamp)  
Dryer might have not been started by using the «On/Off» button. Make sure that the  
dryer is on.  
Bulb may have blown. Call the authorized service to replace the bulb.  
“Final / Anti-creasing” LED flashes.  
The 2-hour anti creasing programme to prevent laundry from creasing might have  
been activated. Turn off the dryer and take out the laundry.  
“Final / Anti-creasing” LED is on.  
Programme has come to an end. Turn off the dryer and take out the laundry.  
The “Drying” LED flashes.  
A heat sensor failure has occurred. Dryer ends the programme without heating. Turn  
off the dryer and take out the laundry. Call your authorized service  
• “Filter cleaning” LED is on.  
Filter might have not been cleaned. Clean the cover filter.  
“Water comes out the cover”  
Clean the entire inner surface of the cover and door gasket.  
“Cover opens spontaneously.”  
Push it until you hear that it is closed.  
For products with a condenser:  
“Water tank” warning LED is on.  
Water may be full. Drain the water in the tank.  
“Condenser cleaning” LED is on.  
Condenser might have not been cleaned. Clean the filters in the condenser under the  
kick plate.  
ACall an authorized service if the problem persists.  
 
22 EN  
9 Guarantee  
Your new product is guaranteed against the  
cost of breakdown repairs for twelve months  
from the date of the original purchase.  
Important notes  
Your product is designed and built for  
domestic household use only.  
• The guarantee will be void if the product  
is installed or used in commercial or non-  
residential domestic household premises.  
• The product must be correctly installed,  
located and operated in accordance with  
the instructions contained in the User  
Instructions Booklet provided.  
• Professional installation by a qualified  
Electrical Domestic Appliance Installer  
is recommended for all Washing  
Machines,Tumble Dryers, Dishwashers,  
Dryers and Electric Cookers  
What is covered?  
• Repairs necessary as a result of faulty  
materials, defective components or  
manufacturing defect.  
• The cost of functional replacement parts,  
but excluding consumable items.  
• The labour costs of a approved repairer to  
carry out the repair.  
What is not covered?  
Transit, delivery or accidental damage or  
misuse and abuse.  
• Cabinet or appearance parts, including  
knobs, flaps, handles or container lids.  
• Accessories or consumable items including  
but not limited to, ice trays, scrapers, cutlery  
baskets, filters and light bulbs.  
• Gas Cookers must only be installed by a  
Gas safe registered Gas Installer.  
• The guarantee is given only within the  
boundaries of the United Kingdom and the  
Republic of Ireland.  
• Repairs required as a result of unauthorised  
repair or inexpert installation that fails to  
meet the requirements contained in the user  
instruction book.  
• Repairs to products used on commercial  
or non-residential household premises.  
• Loss of frozen food in freezers or fridge/  
freezers. (Food loss insurance is often  
included within your household contents  
insurance policy, or may be available  
• The guarantee is applicable only to new  
products and is not transferable if the  
product is resold.  
• disclaims any liability for incidental or  
consequential damages.  
• The guarantee does not in anyway diminish  
your statutory or legal rights.  
separately from your retailer).  
 
23 EN  
10 Service  
Please keep your purchase receipt or other  
proof of purchase in a safe place; you will  
need to have it should the product require  
attention under guarantee.  
You should also complete the details below;  
it will help us assist you when requesting  
service. (The model number is printed on the  
Instruction Booklet and the serial number  
is printed on the Rating Label affixed to the  
appliance)  
Service once the manufacturers  
guarantee has expired.  
If you have purchased an extended  
guarantee please refer to the instructions  
contained within the extended guarantee  
agreement document. Otherwise please call  
the appropriate number above where service  
can be obtained at a charge.  
Should you experience any difficulty in  
obtaining service please contact the  
Customer Help-Line.  
Tel: 0845 600 4911  
Model No:  
Serial No:  
Retailer:  
Date of purchase:  
For service under guarantee simply  
telephone the appropriate number below.  
UK Mainland & Northern Ireland  
Fridges & Freezers 0845 600 4903  
Electric Cookers 0845 600 4902  
Gas & 0845 600 4905  
Republic of Ireland  
Dual Fuel Cookers  
All Refrigeration, 01 862 3411  
All Cookers  
Washing Machines & Dryers  
Tumble Dryers 0845 600 4906  
Washing Machines & Dryers, Tumble Dryers  
Dishwashers  
Before requesting service please check the  
trouble-shooting guide in the Operating  
Instructions as a charge may be levied where  
no fault is found even though your product  
may still be under guarantee.  
 
24 EN  
 
 
 
 

Acu Rite Router CNC 3500i User Manual
Addonics Technologies Computer Drive HDUSI325AES User Manual
AEG Convection Oven BP5003021 User Manual
Alto Shaam Refrigerator QC 100 User Manual
American Audio Turntable TTB 2010 User Manual
American Dryer Corp Clothes Dryer AD 530 User Manual
AOpen Computer Hardware DX34 User Manual
AO Smith Water Heater PGCL 40 User Manual
Atlas Sound Switch AM1100 User Manual
Atlona TV Converter Box AT 3GSDI HD User Manual