Beko Refrigerator TLD 673 APB User Manual

Tall Larder  
Fridge  
TLD 673 APB  
TLD 673 APW  
 
CONTENTS  
1 Your refrigerator  
2 Warnings  
ELECTRICAL REQUIREMENTS.........5  
WARNING! THIS APPLIANCE MUST  
BE EARTHED....................................5  
3
4
5 Using your refrigerator 15  
CHILLER ZONE COMPARTMENT  
DRAWER.........................................15  
Water dispenser ..............................17  
6 Maintenance and  
cleaning  
19  
20  
3 Installation  
7
7 Do’s and Don’ts  
TRANSPORTATION INSTRUCTIONS.7  
INSTALLATION INSTRUCTIONS........7  
REPLACING THE INTERIOR LIGHT  
BULB .............................................10  
REVERSING THE DOORS...............11  
4 Before operating  
14  
STARTING.......................................14  
EN  
2
 
1 Your refrigerator  
Congratulations on your choice of a BEKO quality Appliance which has been  
designed to give you service for many years.  
1
10  
2
3
4
5
12  
6
5
5
5
11  
10  
5
7
13  
8
9
1.  
2.  
3.  
4.  
5.  
6.  
Front plastic trim  
Interior light  
Fan  
Thermostat knob  
Movable shelves  
Wine rack  
7.  
8.  
9.  
0 °C Compartment  
Crisper  
Adjustable front feet  
10. Adjustable door shelves  
11. Egg compartment  
12. Water Dispenser  
13. Bottle shelf  
C Figures that take place in this instruction manual are schematic and may not  
correspond exactly with your product. If the subject parts are not included in the  
product you have purchased, then it is valid for other models.  
EN  
3
 
2 Warnings  
To obtain the best possible  
•DO NOT connect your appliance to  
the electricity supply until all packing  
and transit protectors have been  
removed.  
• Leave to stand for at least 4  
hours before switching on to allow  
compressor oil to settle if transported  
horizontally.  
performance and trouble free operation  
from your appliance it is very important  
to carefully read these instructions.  
• On delivery, check to make sure that  
the product is not damaged and that  
all the parts and accessories are in  
perfect condition.  
• Ensure that the plug remains readily  
accessible. Do not use multiple  
adapter bar or extension cable.  
• Failure to observe these instructions  
may invalidate your right to free service  
during the guarantee period.  
• If you are discarding an old  
refrigerator with a lock or latch fitted  
to the door, disable the lock/latch,  
ensure that it is left in a safe condition  
to prevent the entrapment of young  
children.  
• This fridge/freezer must only be used  
for its intended purpose i.e the storing  
and freezing of edible foodstuff.  
• Do not dispose of the appliance on a  
fire. At BEKO, the care and protection  
of our environment is an ongoing  
commitment. This appliance which  
is among the latest range introduced  
is particularly environment friendly.  
Your appliance contains non CFC /  
HFC natural substances in the cooling  
system (Called R600a) and in the  
insulation (Called cyclopentane) which  
are potentially flammable if exposed  
to fire. Therefore, take care not to  
damage, the cooling circuit / pipes of  
the appliance in transportation and in  
use. In case of damage do not expose  
the appliance to fire or potential  
ignition source and immediately  
ventilate the room where the appliance  
is situated.  
• Keep ventilation openings, in the  
appliance enclosure or in the built-in  
structure, clear of obstruction.  
• Do not use mechanical devices  
or other means to accelerate the  
defrosting process, other than those  
recommended by the manufacturer.  
• Do not damage the refrigerant circuit.  
• Do not use electrical appliances  
inside the food storage compartments  
of the appliance, unless they are  
of the type recommended by the  
manufacturer.  
• We suggest you keep these  
instructions in a safe place for easy  
reference.  
• This appliance is not intended for use  
by persons (including children) with  
reduced physical, sensory or mental  
capabilities, or lack of experience  
and knowledge, unless they have  
been given supervision or instruction  
concerning use of the appliance by a  
person responsible for their safety.  
• Children should be supervised to  
ensure that they do not play  
• We suggest you contact your local  
authority for disposal information and  
facilities available.  
with the appliance.  
EN  
4
 
ELECTRICAL  
WARNING! THIS APPLIANCE  
MUST BE EARTHED  
If the fitted moulded plug is not  
suitable for your socket, then the plug  
should be cut off and an appropriate  
REQUIREMENTS  
Before you insert the plug into the wall  
socket make sure that the voltage and  
the frequency shown on the rating  
plate inside the appliance corresponds plug fitted. Destroy the old plug which  
to your electricity supply.  
Rating label is on the left hand side of  
fridge inner liner.  
is cut off as a plug with bared cord  
could cause a shock hazard if inserted  
into a socket elsewhere in the house.  
The moulded plug on this appliance  
incorporates a 13 A fuse. Should  
the fuse need to be replaced an  
ASTABEAB approved BS 1362 fuse  
of the same rating must be used. Do  
not forget to refit the fuse cover. In the  
event of losing the fuse cover the plug  
must not be used until a replacement  
fuse cover has been fitted. Colour  
of the replacement fuse cover must  
be the same colour as that visible on  
the pin face of the plug. Fuse covers  
are available from any good electrical  
store.  
We recommend that this appliance be  
connected to the mains supply via a  
suitable switched and fused socket.  
The appliance must be positioned so  
that the plug is accessible.  
Should the mains lead of the appliance  
become damaged or should it need  
replacing at any time, it must be  
replaced by a special purpose made  
mains lead which can only be obtained  
from a BEKO Authorised Service  
Agent.  
EN  
5
 
IMPORTANT! FITTING A  
DIFFERENT PLUG  
As the colours of the wires in the  
mains lead of this appliance may  
not correspond with the coloured  
markings identifying the terminals in  
your plug proceed as follows: (See  
diagram).  
6mm.  
GREEN &  
YELLOW  
OR  
GREEN  
L
BROWN  
OR  
RED  
N
22mm.  
BLUE  
OR  
BLACK  
CORD GRIP  
1. Connect the green-yellow or green  
(Earth) wire to the terminal in the plug  
marked ‘E’ or with the symbol  
or  
coloured green and yellow or green.  
2. Connect the blue (Neutral) wire to  
the terminal in the plug marked ‘N’ or  
coloured black.  
3. Connect the brown (Live) wire to  
the terminal in the plug marked ‘Lor  
coloured red.  
With alternative plugs a 13 A fuse must  
be fitted either in the plug or adaptor  
or in the main fuse box. If in doubt  
contact a qualified electrician.  
EN  
6
 
3 Installation  
TRANSPORTATION  
Do not attempt to sit or stand on top  
of your appliance as it is not designed  
for such use. You could injure yourself  
or damage the appliance.  
“IMPORTANT: Make sure that  
mains cable is not caught under the  
appliance during and after carrying  
/ moving the appliance, to avoid  
the mains cable becoming cut or  
damaged.”  
Do not allow children to play with the  
appliance or tamper with the controls.  
V plc declines to accept any liability  
should the instructions not be  
followed.  
INSTRUCTIONS  
1. The appliance should be  
transported only in a vertical upright  
position. The packing as supplied  
must be intact during transportation.  
2. If during the course of transport  
the appliance has to be transported  
horizontally, it must only be laid on its  
right hand side when standing in the  
frontof the appliance. After bringing  
it to upright position,it must not be  
operated for at least 4 hours to allow  
the system to settle.  
3. Failure to comply with the  
above instructions could result in  
damage occuring to the appliance.  
The manufacturer will not be held  
responsible if these instructions are  
disregarded.  
4. The appliance must be protected  
against rain, moisture and other  
atmospheric influences.  
INSTALLATION  
INSTRUCTIONS  
1. The space in the room where the  
appliance is installed must not be  
smaller than 10 cubic metres.  
2. If possible avoid placing the  
appliance near cookers, radiators or  
in direct sunlight as this will cause the  
compressor to run for long periods.  
If installed next to a source of heat  
or refrigerator, maintain the following  
minimum side clearances:  
5. When positioning your appliance  
take care not to damage your flooring,  
pipes, wall coverings etc. Do not move  
the appliance by pulling by the door or  
handle.  
6. Empty any water in the drain  
tray before moving. See section  
‘Defrosting’ and ‘Care & cleaning’ for  
further information.  
IMPORTANT : Care must be taken  
while cleaning / carrying the appliance  
to avoid touching the bottom of the  
condenser metal wires at the back of  
the appliance as you might injure your  
fingers and hands.  
IMPORTANT : This appliance is not  
designed for stacking with any other  
appliance.  
EN  
7
 
From Cookers  
From Radiators  
From Refrigerators or Freezers  
2” (50 mm)  
12” (300 mm)  
1” (25 mm)  
beetween +10 and +32 degrees C  
(50 and 90 degrees F).Therefore if the  
appliance is installed in an unheated /  
cold room (E.g.: Conservatory /annex /  
shed / garage etc.) then the appliance  
may not operate and as a result the  
storage time of food may be reduced.  
8. A special receptacle is supplied to  
store the mains plug during transit.  
The receptacle is fixed at the back of  
the cabinet, on the right hand side of  
the compressor. (See diagram) Gently  
remove the plug from the receptacle.  
Never pull the mains cord, you may  
damage the appliance.  
Allow a minimum of 60 mm (2.4  
inches) between the top of the fridge  
and the ceiling or the underside of a  
wall cupboard.  
3. Make sure that sufficient room is  
provided around the appliance to  
ensure free air circulation.  
In the case of transportation, ensure  
you locate the plug in the receptacle  
provided to avoid transit damage.  
4. Fit the two plastic wall spacers  
supplied with the appliance rotating  
1/4 turn to the condenser at the back  
of the refrigerator (see diagram).  
5. The appliance should be located on  
a smooth surface. The two front feet  
can be adjusted as required. To ensure  
that your appliance is standing upright  
adjust the two front feet by turning  
clockwise or anti-clockwise, until the  
product is in firm contact with the  
floor. Correct adjustment of feet avoids  
excessive vibration and noise.  
6. Refer to cleaning and care section  
to prepare your appliance for use.  
7. This appliance has been designed  
to operate in ambient temperatures  
The following guidelines and  
recommendations are suggested to  
obtain the best results and storage  
hygiene.  
1. The larder fridge is suitable for the  
short term storage of fresh food and  
drinks.  
2. Cooked dishes must be stored in  
airtight covered containers.  
EN  
8
 
3. Fresh wrapped produce can be  
placed on the shelf. Fresh fruit and  
vegetables should be cleaned and  
stored in the salad crisper bin.  
4. Bottles can be placed upright in  
the door rack.  
5. To store raw meat, wrap in  
polythene bags and place in the Chiller  
Zone Compartment . Do not allow to  
behind the Chiller Zone Compartment  
drawer and is evaporated in a special  
container at the back of the appliance  
(see diagrams).  
Ensure that the container is fixed  
properly above the compressor.During  
defrosting water droplets may form at  
the back of the larder  
refrigerator where concealed  
come into contact with cooked food to evaporator is located. Some droplets  
avoid contamination. For safety, only  
store raw meat for two to three days.  
6. Keep the food packed, wrapped  
or covered. Allow hot food and  
may remain on the liner and refreeze  
when defrosting is completed.  
Do not use pointed or sharp edged  
objects such as knives, forks to  
beverages to cool before placing them remove the droplets which have  
in the fridge. Do not store poisonous  
or dangerous substances in the  
refrigerator. High proof alcohol must  
be stored upright in sealed containers.  
Left over canned food should not be  
stored in the can.  
7. Some fruit and vegetables suffer  
damage if kept at temperatures near  
0 degrees centigrade. Therefore  
wrap pineapples, melon, cucumbers,  
tomatoes and similar produce in  
polythene bags.  
refreezed.  
If at any time the defrost water  
does not drain from the collection  
channel,remove the Chiller Zone  
Compartment drawer and check to  
ensure that no food particles have  
blocked the drain tube. The drain tube  
can be cleared by pushing the special  
plastic plunger provided down the  
drain tube (2)  
2
8. Do not leave frozen food at room  
temperature to thaw; the best way to  
defrost food is to put it in the fridge  
to thaw slowly. Make sure you avoid  
defrosting food or food juices drip onto  
other food.  
1
DEFROSTING  
The larder refrigerator defrosts  
automatically. The defrosting water  
runs to the drain tube via a collection  
channel (1)  
Special Container  
Compressor  
EN  
9
 
REPLACING THE INTERIOR  
LIGHT BULB  
Should the light fail to work, proceed  
as follows.  
1. Switch off at the socket outlet and  
pull out the mains plug.  
You may find it useful to remove  
shelves for easy access.  
2. Remove the light diffuser cover  
screw. Use cross-headed screw driver.  
3. Pull off the light diffuser cover and  
remove the light bulb.  
4. Replace the burnt-out light bulb.  
5. Reassemble reversing the sequence  
and operations. First ensure the top of  
the cover is in place.  
6. Carefully dispose of the burnt-out  
light bulb immediately.  
“Replacement light bulb can easily be  
obtained from a good local electrical or  
DIYstore.”  
EN  
10  
 
3. Gently prise off plastic hinge covers  
on both sides of front top panel using  
a small flat-headed screwdriver. (1-2)  
4. Unscrew the bolts of the top hinge  
and remove top hinge. (3)  
REVERSING THE DOORS  
We recommend that you reverse doors  
before switching on for the first time.  
5. Remove door carefully off the  
bottom hinge and stand door upright  
in a safe place.(4)  
Tools required: Small and medium size  
flat and cross-headed screwdrivers, a  
pair of pliers.  
6. Gently prise off plastic hinge cover  
on door top trim. Fit the other door top  
trim plastic off hinge cover supplied in  
the plastic bag.(5)  
Spare Parts supplied in the plastic  
bag: The following parts, which are  
exclusively for left hand side fitted  
hinge operation are supplied in a  
plastic bag with the appliance:  
7. Gently tilt the appliance back  
against a strong wall on its rear side  
sufficiently to allow the lower hinge  
to be removed. Take care to protect  
the appliance, your wall and floor  
coverings. You can utilise the original  
packaging to do this.Once you tilt the  
appliance back, check to make sure  
the appliance is completely stable and  
safe before you carry on. (6)  
8.Unscrew and remove the front feet  
and 1 bolt. (7)  
9. Unscrew and remove the bottom  
hinge. (8)  
- Door top trim hinge covers – there  
are 2 different parts, one for each side  
of top trim..  
We suggest you keep all the parts  
supplied in the plastic bag and also  
parts, which have been removed when  
reversing doors, in a safe place for  
possible future, re-use.  
IMPORTANT: We suggest you ask  
somebody to help you when moving  
the appliance around and to hold  
doors when removing / re-fitting  
hinges and doors to avoid any injury  
and damage to the product.  
10. Unscrew and remove the bottom  
hinge door stopper and bushing and  
reposition them on the other side while  
rotating the bushing 180°. (9)  
11. Fit the bottom hinge and tighten  
the screws as shown in figure. (10)  
12. Fit the other front feet as shown in  
figure. (11)  
13. Rotate the top hinge 180°.  
Unscrew the hinge pin and re-tighten it  
to the opposite side. (12)  
14. Fit the top hinge on the left hand  
side bushing of the door. (13)  
15. Locate and re-fit door to bottom  
hinge pin. (14)  
Please refer to diagrams supplied. To  
follow numbers in brackets below,  
refer to the main diagram.  
1. Switch off the appliance at the  
socket outlet and pull out the mains  
plug.  
2. Remove all loose items and fittings  
and food inside the appliance.  
EN  
11  
 
16. Re-fit the upper hinge on the  
opposite side by using a flat headed  
screwdriver. (15)  
17. Fit front top panel plastic hinge  
covers on the opposite sides. (16)  
18. Remove the handle cover gently  
taking care not to damage the  
appliance.(17)  
19. Unscrew and remove the handle  
(18). Do not unscrew the yellow  
coloured screws!  
20. Rotate 180 degrees and fit handle  
to the other side after removing hole  
plugs gently.(19,20)  
21. Fit the handle cover.(21)  
22. Adjust the two front feet if  
necessary.  
23. Check that door opens and closes  
easily, it is aligned correctly and there  
are no gaps allowing air into the  
cabinet. If here are gaps between the  
door seal and the cabinet, adjust the  
door seal by gently pulling away from  
the door using fingers.  
24. Check that all the hinge screws are  
tightened. Avoid over tightening the  
screws.  
25. Put all items, fittings back in the  
appliance.  
26. Wait for at least 4 hours to allow  
the system to settle before switching  
on.  
27. Once the correct storage  
temperatures have been reached in  
the appliance, put back all the food.  
EN  
12  
 
1
6
3
6
4
2
7
5
45°  
9
8
10  
15  
17  
17  
13  
13  
16  
180°  
21  
22  
19  
18  
14  
20  
12  
11  
EN  
 
13  
4 Before operating  
STARTING  
Important Note :  
Final Check  
Ice formation at the back is normal, do  
not worry. (See Defrosting) fan guard  
as they may cause the cooling system  
to block and therefore operate less  
efficiently.  
Before you start using the refrigerator  
check that:  
1.The front feet have been adjusted  
so the appliance is level.  
2.The interior is dry and air can  
circulate freely.  
3.Clean the interior as recommended  
under “CLEANING AND CARE.”  
4.Insert the plug into the wall socket  
and switch on the electricity supply.  
When the door is open the interior light  
will come on.  
5.You will hear a noise as the  
compressor starts up. The liquid and  
gases sealed within the refrigeration  
system may also give rise to noise,  
whether the compressor is running or  
not which is quite normal.  
6. We recommend that you set the  
thermostat knob at 3 (three) and  
monitor the temperature to ensure the  
appliance  
maintains desired storage  
temperatures (See section  
Temperature Control and Adjustment).  
7. Do not load the appliance  
immediately it is switched on. Wait until  
the correct storage temperature has  
been reached.  
We recommend that you check  
the temperature with an accurate  
thermometer  
(see; Temperature Control and  
Adjustment).  
EN  
14  
 
5 Using your refrigerator  
TEMPERATURE CONTROL AND ADJUSTMENT OF FRIDGE  
Remember you must take your reading  
very quickly since the thermometer  
temperature will rise very rapidly after  
you remove it from the appliance.  
Please remember each time the door  
is opened cold air escapes and the  
internal temperature rises. Therefore  
never leave the door open and ensure  
it is closed immediately after food is  
put in or removed.  
Operating temperatures are controlled  
by the thermostat knob (Fig. 1) and  
In case of a temporary ice build up in  
may be set at any position between 1  
the fridge compartment, reduce the  
and  
thermostat setting to 1. Once the ice  
build up disappears and the appliance  
starts auto defrosting again as normal,  
then you may increase the thermostat  
5, 5 being the coldest position.  
Towards 5 you will obtain a colder  
fridge temperature and vice versa. Set  
the thermostat  
setting, if required.  
knob to ensure an average of +5 °C  
(40°F) is achieved in the fridge and  
between -1.5 °C and +3°C is achieved  
in the Chiller Zone Compartment after  
24 hours.  
(Fig. 2) shows how you can switch  
off the appliance completely: Turn the  
thermostat knob to “0” (Zero) position.  
The average temperature inside  
the fridge depends on the following  
factors:  
CHILLER ZONE  
COMPARTMENT DRAWER  
Chiller Zone Compartment Drawer is  
ideal for storage of fresh fish, meat  
and easily perishable food like cooked  
chilled food. In order to best utilise  
this compartment, we recommend the  
following;  
• Ambient temperature in the room  
(seasonal changes)  
• Frequency of door opening  
• Placing hot food inside the product  
• Position of the product  
We recommend that you check  
the temperature with an accurate  
thermometer to ensure that the  
storage compartments are kept to the  
desired temperature.  
EN  
15  
 
Monitor the temperature using an accurate fridge thermometer to ensure that  
the storage temperature is in the following range; approximately between -1.5  
degrees C and +3 degrees C. Below thermostat setting positions are suggested  
to start with;  
Approximate ambient temperature in the  
room where the appliance is (degrees C)  
10 degrees C  
16 degrees C  
20 degrees C  
Suggested thermostat knob setting  
range *  
1 to 2  
1 1/2 to 2 1/2  
2 to 3  
2 1/2 to 3 1/2  
2 1/2 to 4  
25 degrees C  
32 degrees C  
If above settings could not maintain  
the required temperatures, then adjust  
the thermostat knob accordingly; to  
obtain a colder temperature, turn the  
thermostat knob towards 5 and vice  
versa.  
*Also see factors affecting  
temperature inside the fridge on page  
8 and adjust  
it accordingly to suit  
your specific situation.  
Warning!  
Do not remove this glass shelf;  
otherwise Chiller Zone Compartment  
will not function to specifications.  
EN  
 
16  
Filling in the water tank of water  
dispenser  
Open the cap of the water tank as  
illustrated in the figure. Fill in with pure  
and clean drinking water. Close the  
cap.  
Water dispenser  
Water dispenser is a very useful feature  
to obtain chilled water without opening  
the door of your fridge. Since you do  
not have to open the door of your  
fridge frequently, you also save on  
electricitiy.  
Caution!  
• Do not fill water tank with any liquid  
other than drinking water; beverages  
such as fruit juice, carbonated fizzy  
soda drinks, alcoholic drinks are not  
suitable for use with water dispenser.  
If such liquids are used, the water  
dispenser will malfunction and may  
be damaged beyond repair. The  
guarantee does not cover such uses.  
Some chemical ingredients and  
additives in such drinks / beverages  
may also attack and damage water  
tank material.  
Using the water dispenser  
Push in the lever of the water  
• Only use clean pure drinking water.  
• Capacity of water dispenser tank is 2.2  
litres [3.8 pints], do not overfill.  
• Push the water dispenser lever with  
a rigid cup. If you are using a plastic  
disposable cup, then push the lever  
with your fingers from behind the cup.  
dispenser with your glass. By releasing  
the lever, you cut off the dispensing.  
When operating the water dispenser,  
maximum flow is achieved by fully  
depressing the lever. Please note, how  
much water flows from the dispenser  
depends on how far you depress the  
lever. As the level of water in your  
cup / glass rises, gently reduce the  
amount of pressure on the lever to  
avoid overflow. If you depress the lever  
a small amount, then water will trickle;  
this is perfectly normal and is not a  
fault.  
EN  
17  
 
Cleaning the water tank  
Remove the water tank, open the  
latches on both sides and detach the  
top cover mechanism from the water  
tank. Clean the water tank with warm  
clean water, reinstall the top cover  
mechanism and fasten the latches.  
When installing the water tank, make  
sure that hooks behind it fits securely  
into the hangers on the door. Make  
sure that parts removed during  
cleaning (if any) are installed correctly  
into their original locations. Otherwise,  
water may leak.  
Important:  
Water tank and components of water  
dispenser are not dishwasher-proof.  
Water tray  
Water that drips while using the water  
dispenser accumulates in the drip tray  
housing.Remove the drip tray firstly  
pressing up from the front edge then  
pulling towards yourself.Then clean  
drip housing by a fabric or sponge that  
has water absorbtion tendency.  
Safety lock for Water Dispenser  
You may use the lock in order to avoid  
small children tampering with the water  
dispenser. To do this, slide the locking  
latch from left to right as illustrated in  
the figure. You must slide the latch  
back to left position in order to use the  
water dispenser.  
UNLOCK  
LOCK  
To avoid accidental water dispensing,  
we recommend you to lock the water  
dispenser.  
Maximum height of glass suitable for  
use with Stored Water Dispenser is  
16 cm which includes most of the  
“Standard” pint glasses.  
EN  
18  
 
6 Maintenance and cleaning  
** We recommend that you switch  
off the appliance at the socket outlet  
and pull out the mains plug before  
cleaning.  
** Check door seals regularly to ensure  
they are clean and free from food  
particles.  
** Removal of door rack :  
** Never use any sharp abrasive  
instrument, soap, household cleaner,  
detergent and wax polish for cleaning.  
** To remove a door rack, remove all  
the contents and then simply push the  
door tray upwards from the base.  
** Use luke warm water to clean the  
cabinet of the appliance and wipe it  
dry.  
** Make sure that the special plastic  
container (drain tray) at the back of  
the appliance which collects defrost  
water is clean at all times. If you want  
to remove the tray to clean it follow the  
instructions below :  
• Switch off at the socket outlet and  
pull out the mains plug.  
• Push the lug down with the tip of  
a screw driver & pull out firmly.  
• Clean the drain tray and wipe it  
dry.  
** Use a damp cloth wrung out  
in a solution of one teaspoon of  
bicarbonate of soda to one pint of  
water to clean the interior and wipe it  
dry.  
** Make sure that no water enters the  
temperature control box.  
** If the larder refrigerator is not going  
to be used for a long period of time  
switch it off, remove all food, clean it  
and leave the door ajar.  
• Reassemble reversing the  
sequence and operations.  
** Removal of Chiller Zone  
** Any dust that gathers on the  
condenser, which is located at the  
back of the appliance, should be  
removed once a year with a vacuum  
cleaner.  
Compartment Drawer:  
Pull it out as far as possible and then  
lift up and remove it completely.  
Should the light fail to work switch off  
at the socket outlet and pull out the  
mains plug.  
Use a cross headed screw driver to  
remove the light diffuser cover.  
Then ensure the bulb is screwed in  
until it is secure in the bulb holder.  
Replace the plug and switch on.  
If the bulb functions, reassemble by  
reversing the above procedure, ensure  
the top cover is in place.  
EN  
19  
 
7 Do’s and Don’ts  
Dont- Consume food which has been  
stored for an excessive time in the  
larder refrigerator.  
Dont- Store cooked and fresh food  
together in the same container.  
They should be packaged and  
stored separately..  
Dont- Let defrosting food or food  
juices drip onto food in your larder  
refrigerator.  
Dont- Clean your larder refrigerator  
regularly.  
Dont- Keep raw meat and poultry  
below cooked food and dairy  
products and ideally in the chiller  
zone compartment drawer.  
Dont- Keep food for as short a time  
as possible and adhere to ‘Best  
Before’ and “Use By” dates.  
Dont- Take off any unusable leaves on  
vegetables and wipe off any soil.  
Dont- Leave lettuce, cabbage, parsley  
and cauliflower on the stem.  
Dont- Wrap cheese firstly in  
greaseproof paper and then in a  
polythene bag excluding as much  
air as possible.  
PROBLEM SOLVING  
If the appliance does not operate when  
switched on, check whether:  
• The plug is inserted properly in the  
socket and that the power supply  
is on. (To check the power supply  
to the socket, plug in another  
appliance)  
• The fuse has blown/circuit breaker  
has tripped/main distribution  
switch has been turned off.  
• The temperature control has been  
set correctly.  
• New plug is wired correctly if you  
have changed the fitted moulded  
plug.  
If the appliance is still not operating  
after the above checks, please  
refer to the section on “How To  
Obtain Service”.  
Dont- Wrap meat, fish and offal in  
polythene bags.  
Dont- Wrap bread well to keep it  
fresh..  
Dont- Chill white wines, beer, lager  
and mineral water before serving.  
Dont- Bananas in your fridge.  
Dont- Melon in your fridge. It can be  
chilled for short periods as long as  
it is wrapped to avoid it flavouring  
other food.  
Dont- The door open for long periods  
as this will make the larder  
refrigerator more costly to run.  
Dont- Poisonous or any dangerous  
substances in the larder  
Please ensure that above checks have  
been made as a charge will be  
made if nofault is found.  
refrigerator.Your larder refrigerator  
has been  
designed for the storage of edible  
foodstuffs only.  
EN  
20  
 
HOW TO OBTAIN SERVICE  
Please keep your purchase receipt or other proof of purchase in a safe place;  
you will need to have it should the product require attention under guarantee.  
You should also complete the details below; it will help us assist you when requesting  
service. (The model number is printed on the Instruction Booklet and the serial  
number is printed on the Rating Label affixed to the appliance)  
Model No:  
Serial No:  
Retailer:  
Date of purchase:  
For service under guarantee simply telephone the appropriate number below  
UK Mainland & Northern Ireland  
Fridges & Freezers  
Electric Cookers  
Gas & Dual Fuel Cookers  
Washing Machines  
& Dishwashers  
0845 6004903  
0845 6004902  
0845 6004905  
0845 6004906  
Republic of Ireland  
All Refrigeration, All Cookers  
Washing Machines & Dishwashers  
01 862 3411  
Before requesting service please check the trouble-shooting guide in the Operating  
Instructions as a charge may be levied where no fault is found even though your  
product may still be under guarantee.  
Service once the manufacturers guarantee has expired.  
If you have purchased an extended guarantee please refer to the instructions  
contained within the extended guarantee agreement document. Otherwise please  
call the appropriate number above where service can be obtained at a charge.  
Should you experience any difficulty in obtaining service please contact the Beko  
Customer Help-Line.  
Tel: 0845 6004911 e-mail: [email protected]  
EN  
21  
 
GUARANTEE DETAILS  
Your new Beko product is guaranteed against the cost of breakdown repair for  
twelve months from the date of the original purchase.  
What is covered?  
Repairs necessary as a result of faulty materials, defective components or  
manufacturing defect.  
The cost of functional replacement parts, but excluding consumable items.  
The labour costs of a Beko approved repairer to carry out the repair.  
What is not covered?  
Transit, delivery or accidental damage or misuse and abuse.  
• Cabinet or appearance parts, including knobs, flaps, handles or container  
lids.  
Accessories or consumable items including but not limited to, ice trays,  
scrapers, cutlery baskets, filters and light bulbs.  
Repairs required as a result of unauthorised repair or inexpert installation that  
fails to meet the requirements contained in the user instruction book.  
Repairs to products used on commercial or non-residential household  
premises.  
Loss of frozen food in freezers or fridge/freezers. (Food loss insurance is  
often included within your household contents insurance policy, or may be  
available separately from your retailer).  
Important notes.  
Your Beko product is designed and built for domestic household use only.  
The guarantee will be void if the product is installed or used in commercial  
or non-residential domestic household premises.  
The product must be correctly installed, located and operated in accordance  
with the instructions contained in the User Instructions Booklet provided.  
Professional installation by a qualified Electrical Domestic Appliance Installer  
is recommended for all Washing Machines, Dishwashers and Electric Cookers  
• Gas Cookers must only be installed by a Gas Safe (or BORD GAIS) registered  
Gas Installer.  
The guarantee is given only within the boundaries of the United Kingdom  
and the Republic of Ireland.  
The guarantee is applicable only to new products and is not transferable if  
the product is resold.  
Beko disclaims any liability for incidental or consequential damages.  
The guarantee does not in anyway diminish your statutory or legal rights.  
EN  
22  
 
BEKO plc  
Beko House  
Caxton Way  
Watford  
Hertfordshire  
WD18 8UF  
Tel: 0845 6004911  
Fax: 0845 6004922  
Printed in Turkey  
48 9724 0001  
Part no:  
AA  
Revision no:  
 

3Com Digital Camera iCV 01a User Manual
8e6 Technologies Network Card ER 40 User Manual
Agri Fab Outdoor Cart 45 02402 ATV User Manual
Altec Lansing Portable Speaker 405A User Manual
Altinex Stereo Amplifier DA1203RM User Manual
American Dryer Corp Clothes Dryer AD 531 User Manual
American Standard Outdoor Shower T03850X User Manual
Audiovox Remote Starter APS 787 User Manual
Avenview TV Converter Box HDMI 3G HD SD SDI User Manual
Eureka Tents Tent Northern Breeze User Manual