Beko Ventilation Hood HBV60X User Manual

Chimney Hood - Model:  
HBV60X  
GB COOKER HOOD - User instructions  
 
Fig.1  
Fig.2  
- 3 -  
 
Fig.3  
Fig.4  
Fig.5  
Fig.6  
- 4 -  
 
Fig.7  
INCANDESCENT TUBOLAR LAMP  
- Ø 25mm – L85- E14 – 40W  
CANDLE HALOGEN LAMP  
- Ø 35mm - E14 – 28W  
Fig.8  
- 5 -  
 
a suitable manner, the user is helping to prevent potential  
damage to the environment or to public health.  
GB  
ENGLISH  
The symbol on the product or on the accompanying  
paperwork indicates that the appliance should not be  
treated as domestic waste, but should be delivered to a  
suitable electric and electronic appliance recycling collection  
point. Follow local guidelines when disposing of waste. For  
more information on the treatment, re-use and recycling of  
this product, please contact your local authority, domestic  
waste collection service or the shop where the appliance was  
purchased.  
GENERAL  
Carefully read the following important information regarding  
installation safety and maintenance. Keep this information  
booklet accessible for further reference. The appliance has  
been designed for use in the ducting version (air exhaust to  
the outside – Fig.1B), filtering version (air circulation on the  
inside – Fig.1A) or with external motor (Fig.1C).  
SAFETY PRECAUTION  
INSTALLATION INSTRUCTIONS  
1. Take care when the cooker hood is operating simultane-  
ously with an open fireplace or burner that depend on the air  
in the environment and use a fuel source other than electrical  
energy, as the cooker hood removes the air from the environ-  
ment which a burner or fireplace need for combustion. The  
negative pressure in the environment must not exceed 4Pa  
(4x10-5 bar). Provide adequate ventilation in the environment  
for a safe operation of the cooker hood.Follow the local laws  
applicable for external air evacuation.  
Assembly and electrical connections must be carried out by  
specialised personnel.  
• Electrical Connection  
The appliance has been manufactured as a class II, therefore  
no earth cable is necessary.  
The connection to the mains is carried out as follows:  
BROWN = L line  
BLUE = N neutral  
If not provided, connect a plug for the electrical load indi-  
cated on the description label. Where a plug is provided,  
the cooker hood must be installed in order that the plug is  
easily accessible.  
An omnipolar switch with a minimum opening of 3mm  
between contacts, in line with the electrical load and local  
standards, must be placed between the appliance and the net-  
work in the case of direct connection to the electrical network.  
Before connecting the model to the electricity network:  
- check the data plate (positioned inside the appliance) to as-  
certain that the voltage and power correspond to the network  
and the socket is suitable. If in doubt ask a qualified electrician.  
- If the power supply cable is damaged, it must be replaced  
with another cable or a special assembly, which may be  
obtained direct from the manufacturer or from the Technical  
Assistance Centre.  
- This device must be hardwired to the mains supply network  
by connecting to a single phase spur protected by 3A fuse.  
The minimum distance between the support surfaces of  
the cooking pots on the cooker top and the lowest part of  
the cooker hood must be at least 65 cm. If a connection  
tube composed of two parts is used, the upper part must be  
placed outside the lower part. Do not connect the cooker  
hood exhaust to the same conductor used to circulate hot air  
or for evacuating fumes from other appliances generated by  
other than an electrical source. Before proceeding with the  
assembly operations, remove the anti-grease filter(s) (Fig.6)  
so that the unit is easier to handle.  
2. Warning !  
In certain circumstances electrical appliances may be a  
danger hazard.  
A) Do not check the status of the filters while the cooker  
hood is operating.  
B) Do not touch bulbs or adjacent areas, during or straight  
after prolonged use of the appliance.  
C) Flambè cooking is prohibited underneath the cooker  
hood.  
- In the case of assembly of the appliance in the suction version  
prepare the hole for evacuation of the air.  
D) Avoid leaving exposed flames and always ensure that  
the burners are covered as open flames are damaging for  
the filters and a fire hazard.  
E) Constantly check food frying to avoid overheated oil  
becoming a fire hazard.  
We recommend the use of an air exhaust tube which has the  
same diameter as the air exhaust outlet hole. If a pipe with a  
smaller diameter is used, the efficiency of the product may be  
reduced and its operation may become noisier.  
F) Disconnect the electrical plug prior to any maintenance.  
G) This appliance is not intended for use by young children  
or infirm persons without supervision.  
H) Young children should be supervised to ensure they  
do not play with the appliance.  
• Warning: if the bulbs are not working, ensure that they are  
screwed in fully.  
Installation  
I) There shall be adequate ventilation of the room when  
the rangehood is used at the same time as appliances  
burning gas or other fuels.  
L) There is a risk of fire if cleaning is not carried out in  
accordance with the instructions.  
Prior to proceeding with the assembly operations (according  
to the model that you have purchased), to facilitate handling  
of the device, remove the grille as indicated in Fig. 5.  
The appliance is equipped with 2 air outlets, to be used in  
accordance with your specific requirements: one is located on  
the upper part of the appliance and the other at the rear (Fig.  
1A). The flange D, to which the air exhaust pipe is connected,  
and a plug B, used to shut off the unused air outlet, are both  
This appliance conforms to the European Directive  
EC/2002/96, Waste Electrical and Electronic Equipment  
(WEEE). By making sure that this appliance is disposed of in  
- 6 -  
 
supplied with the product.  
solution of water and neutral liquid detergent, leaving to soak.  
- Rinse thoroughly with warm water and leave to dry.  
- The filters may also be washed in the dishwasher.  
The aluminium panels may alter in colour after several washes.  
This is not cause for customer complaint nor replacement of  
panels.  
• The active carbon filters purify the air that is replaced in the  
environment. The filters are not washable nor re-useable and  
must be replaced at maximum every four months. The satura-  
tion of the active carbon filter depends on the frequency of use  
of the appliance, by the type of cooking and the regularity of  
cleaning the anti-grease filters.  
• Clean the fan and other surfaces of the cooker hood regularly  
using a cloth moistened with denatured alcohol or non abrasive  
liquid detergent.  
• The illumination installation is designed for use during cooking  
and not for prolonged general illumination of the environment.  
Prolonged use of the illumination installation notably reduces  
the duration of the bulb.  
• This device may be installed in two different ways:  
1. Fixing the hood to the lower part of the wall cabinet (Fig.2)  
-Make4holesinthewallcabinetrespectingthemeasurements  
indicated in figures 2 A-2 C.  
- Position the hood underneath the wall cabinet and fix it  
into place using 4 screws (not supplied) suitable for the type  
of cabinet.  
2. Fixing the hood to the wall (Fig.2).  
-Make4holesinthewallcabinetreferringtothemeasurements  
indicated in figures 2 A-2 B. - Hang the hood on the wall, using  
the2holesH,alignitinahorizontalpositionandxitdefinitively  
to the wall using the two lower safety holes I (Fig. 2B). For the  
various installations use screws and screw anchors suited to  
the type of wall (e.g. reinforced concrete, plasterboard, etc.). If  
the screws and screw anchors are provided with the product,  
check that they are suitable for the type of wall on which the  
hood is to be fixed.  
• Replacing the acrylic or metal panels  
To replace the acrylic or metal panels you need to first remove  
the grille D by pushing the two side buttons B inwards as indi-  
cated in figure 5. Remove the two filter clips B (fig. 6) and the  
acrylic or metal panel C. To reassemble the part, simply perform  
the procedure in reverse.  
The hood is already prepared for the version with which it was  
ordered. The versions may be:  
- Extraction (Fig. 1A-3)  
- Filter (Fig. 1B-4-7).  
- If the hood is an extractor model, the lever C must be posi-  
tioned as indicated in Fig. 3.  
- If the hood is a filter model, the lever C must be positioned  
• Replace incandescent/halogen/fluorescent lamps (Fig.8):  
Only use lamps of the same type and Wattage installed on  
the device.  
as indicated in Fig. 4.  
• FILTER REMOVAL  
Extractor version  
WARNING - ENSURE THE APPLIANCE IS SWITCHED OFF AT  
THE MAINS BEFORE REPLACING THE BULBS AND FILTERS.  
1. remove the filters by lifting the recessed handle and lift  
free from the hood frame.  
2. To reinstall the filters position in the recess at the rear  
and press to lock in position.  
The appliance expels the fumes through an outside wall or  
a duct. It is necessary to buy a telescopic pipe in accordance  
with the standards in use (inflammable) and connect it to  
flange D (Fig 1A). The flange D is supplied with the product  
and should be fixed above the air outlet hole of the hood as  
indicated in Fig. 3.  
BULB REPALCEMENT  
1. Remove the filters  
• Filtering version  
To transform an extractor hood version into a filter hood  
version, please inquire with your retailer about purchasing  
charcoal filters. The filters should be fitted to the extraction  
assembly inside the hood, by centring them and rotating them  
90 degrees, until they click into place (Fig. 7). To do this, remove  
the grille D (Fig. 5). Close the air outlet opening with the plug  
B, as indicated in Fig. 4.  
2. Unscrew the bulb in an anti-clock wise direction.  
3. After installing the correct replacement bulb, refit the  
filter.  
Replacement bulbs can be easily obtained from a good  
electrical or DIY store.  
BEFORE CALLING SERVICE/TROUBLE SHOOTING  
The hood was switched on but the unit does not operate.  
• Have you plugged in/switched on the power supply at  
the socket?  
• Check for a blown fuse/or trip.  
Extraction is poor  
• Check and clean the filters if required, if required, if ac-  
tive filters are present replacement filters maybe required.  
• Check that the exhaust ducting is not obstructed.  
USE AND MAINTENANCE  
• It is recommended to operate the appliance prior to cooking.  
It is recommended to leave the appliance in operation for 15  
minutes after cooking is terminated in order to completely  
eliminate cooking vapours and odours.  
The proper function of the cooker hood is conditioned by the  
regularity of the maintenance operations, in particular, the  
active carbon filter.  
• The anti-grease filters capture the grease particles suspended  
in the air, and are therefore subject to clogging according to  
the frequency of the use of the appliance.  
In order to prevent fire hazard, it is recommendable to clean  
the filter at a maximum of 2 months by carrying out the fol-  
lowing instructions:  
THE MANUFACTURER DECLINES ALL RESPONSIBILITY FOR  
EVENTUAL DAMAGES CAUSED BY BREACHING THE ABOVE  
WARNINGS.  
- Remove the filters from the cooker hood and wash them in a  
- 7 -  
 
Guarantee and Service  
Your Beko product is guaranteed against the cost of breackdown repairs for twelve months from the date of  
the original purchase.  
What is covered?  
• All repairs necessary as a result of faulty materials, defective components or manufacturing defect.  
• The cost of all functional replacement parts.  
• The labour costs of a Beko approved repairer to carry out the repair  
What is not covered?  
• Transit or delivery damage  
• Accidental damage  
• Misuse, or abuse.  
• Cabinet or appearance parts, including knobs and flaps  
• Accessory items, including ice trays, scrapers, cutlery baskets  
• Repairs required as a result of unauthorised repairs or inexpert installation that fails to meet the requirements  
contained in the user instruction book.  
• Repairs to products used on commercial or non-residential household premises  
Important notes.  
• The product is guaranteed for domestic household use only.  
• The guarantee will be void if the product is installed or used in commercial or non-residential household  
premises.  
The product must be correctly installed, located and operated in accordance with the instructions contained  
in the User Instructuion Booklet provided.  
• Professional Istrallation by a qualified plumber/electrical appliance installer is recommended for all Washing  
& Dishwashing Machines and Electric Cookers  
• Gas appliances must only be installed by a Gas Safe ( or BORD GAIS) registered Gas Installer.  
• The guarantee is given only within the boundaries of the United Kingdom.  
• The guarantee is not transferable if the product is resold.  
• Beko plc disclaims any liability for incidental or consequential damages  
• The guarantee does not in anyway diminish your statutory or legal rights.  
HOW TO OBTAIN SERVICE UNDER THE MANUFACTURERS WARRANTY  
Please keep your purchase receipt or other proof of purchase in a safe place; you will need to have it should the  
product require attention in the guarantee period  
You should also complete the details below; it will help us assist you quicker when requesting service. ( The  
model number is printed on the Instruction Booklet)  
Model Number:  
Purchased From:  
Date of Purchase:  
---------------------------  
-----------------------------  
---------------------------  
For service under guarantee simply telephone the appropriate number below  
UK Mainland & Northern Ireland  
Fridges & Freezers  
Electric Cookers  
Gas & Dual Fuel Cookers  
Washing Machines & Dishwashers  
0845 600 4903/0345 600 4903  
0845 600 4902/0345 600 4902  
0845 600 4905/0345 600 4905  
0845 600 4906/0345 600 4906  
- 8 -  
 
Republic of Ireland  
All Refrigeration, Cooking, Washing & Dishwashing Machines  
01 862 3411  
Before requesting service please check the trouble-shooting guide in the Operating Instructions as a charge  
may be levied where no faults is found even though your product may still be under guarantee.  
Service once the manufacturers guarantee has expired:  
If you have purchased an extended guarantee please refer to the instructions contained within the extended  
guarantee agreement document. Otherwise please call the above numbers where service can be obtained at  
a charge.  
Should you experience any difficulty in obtaining service please call the  
Beko Customer Help-Line on 0845 600 4911/0345 600 4911  
Beko House, 1 Greenhill Crescent, Watford, Herts. WD18 8QU  
- 9 -  
 
- 10 -  
 
- 11 -  
 
3LIK16XX  
 

Black Box Computer Accessories ACU3001A User Manual
Black Decker Saw BT1400 User Manual
Bock Water heaters Water Heater 541PG User Manual
Bosch Appliances Security Camera VEZ User Manual
Boss Audio Systems Stereo Amplifier FDR 1 User Manual
Bowers Wilkins Speaker 1 SE User Manual
Brother Fax Machine 410 500M User Manual
Carrier Air Conditioner 17DA User Manual
Carrier Air Conditioner 36TE User Manual
Casio Digital Camera QV 5000SX User Manual