Beko Washer wmy 7046LB2 User Manual

Washing Machine  
WMY 7046 LB2  
User’s Manual  
2820524400/ 25-11-14.(10:37)  
Document Number  
 
1 General safety instructions  
This section includes security instructions which may help prevent the  
injuries and material damage risks. All kinds of warranties shall be invalid if  
these instructions are not observed.  
1.1 Life and property safety  
u
Never place the product on a carpet-covered floor. Electrical parts will get  
overheated since air cannot circulate from under the device. This will cause  
problems with your product.  
Unplug the product if it is not in use.  
u
u
Always have the installation and repairing procedures carried out by the  
Authorized Service Agent. Manufacturer shall not be held liable for damages  
that may arise from procedures carried out by unauthorized persons.  
The water supply and draining hoses must be securely fastened and remain  
u
undamaged. Otherwise, water leak may occur.  
While there is still water inside the product, never open the loading door or  
u
remove the filter. Otherwise, risk of flooding and injury from hot water will  
occur.  
Do not force open the locked loading door. Door can be opened a few  
u
minutes after the washing cycle ends. In case of forcing the loading door to  
open, the door and the lock mechanism may get damaged.  
Use detergents, softeners and supplements suitable for automatic washing  
u
machines only.  
u
Follow the instructions on the label of textiles and the detergent package.  
1.2 Children's safety  
u
This product can be used by the children who are at the age of 8 and  
over and the people whose physical, sensory or mental skills are not  
fully developed or who do not have necessary required experience and  
knowledge as long as they are supervised or trained about the safe use of  
the product and its risks. Children should not play with the device. Cleaning  
and maintenance works should not be performed by children unless they  
are supervised by someone. Children of less than 3 years should be kept  
away unless continuously supervised.  
u
Packaging materials may be dangerous for the children. Keep packaging  
materials in a safe place away from reach of the children.  
Electrical products are dangerous for the children. Keep the children away  
u
from the product when it is in use.Do not allow them to play with the product.  
Use child lock to prevent children from intervening with the product.  
 
3 / EN  
Washing Machine / User’s Manual  
u
u
Do not forget to close the loading door when leaving the room where the  
product is located.  
store all detergents and additives in a safe place away from the reach of  
the children by closing the cover of the detergent container or sealing the  
detergent package.  
1.3 Electrical safety  
u
If the product has a failure, it should not be operated unless it is repaired by  
the Authorized Service Agent. Risk of electric shock!  
u
u
This product is designed to resume operating in the event of powering  
on after a power interruption. If you wish to cancel the programme, see  
"Cancelling the programme" section.  
Plug the product into a grounded outlet protected by a 16 A fuse. Do not  
neglect to have the grounding installation made by a qualified electrician.  
Our company shall not be liable for any damages that will arise when the  
product is used without grounding in accordance with the local regulations.  
Do not wash the product by spraying or pouring water onto it! Risk of electric  
shock!  
u
u
Never touch the power cable plug with wet hands! Do not grab the power  
cord to unplug the machine, always unplug it by holding the socket with one  
hand, and pulling the plug with the other hand.  
u
u
Product should be unplugged during installation, maintenance, cleaning  
and repair procedures.  
If the power cable is damaged, it must be replaced by the manufacturer,  
after sales service or a similarly qualified person (preferably an electrician)  
or someone designated by the importer in order to avoid possible risks.  
1.4 Hot surface safety  
While washing the laundry at high temperatures,  
the loading door glass will get hot. Considering  
this fact, during washing operation keep the  
children away from the loading door of the  
product to prevent them touching it.  
 
4 / EN  
Washing Machine / User’s Manual  
2 Important instructions for environment  
2.1 Compliance with WEEE Directive  
This product complies with EU WEEE Directive (2012/19/EU). This product bears a  
classification symbol for waste electrical and electronic equipment (WEEE).  
This product has been manufactured with high quality parts and materials which can be  
reused and are suitable for recycling. Do not dispose of the waste product with normal  
domestic and other wastes at the end of its service life. Take it to the collection center for  
the recycling of electrical and electronic equipment. Please consult your local authorities to  
learn about these collection centers.  
Compliance with RoHS Directive:  
The product you have purchased complies with EU RoHS Directive (2011/65/EU). It does not contain  
harmful and prohibited materials specified in the Directive.  
2.2 Package information  
Packaging materials of the product are manufactured from recyclable materials in accordance with  
our National Environment Regulations. Do not dispose of the packaging materials together with the  
domestic or other wastes. Take them to the packaging material collection points designated by the local  
authorities.  
3 Intended use  
• This product has been designed for domestic use. It is not for commercial purposes or it  
should not be used out of its intended use.  
• The product must only be used for washing and rinsing of laundry that are marked  
accordingly.  
• The manufacturer waives any responsibility arisen from incorrect usage or  
transportation.  
 
5 / EN  
Washing Machine / User’s Manual  
4
Technical specifications  
Supplier name or trademark  
Beko  
Model name  
WMY 7046 LB2  
Rated capacity (kg)  
7
A+++  
1400  
84  
Energy efficiency class / Scale from A (Highest Efficiency) to D (Lowest Efficiency)  
Maximum spin speed (rpm)  
Height (cm)  
Width (cm)  
60  
Depth (cm)  
54  
Net weight ( 4 kg.)  
71  
Single Water inlet / Double Water inlet  
• / -  
• Available  
Electrical input (V/Hz)  
220-240 V / 50Hz  
10  
Total current (A)  
Total power (W)  
2000-2350  
1011  
Main model code  
Technical specifications may be changed without prior notice to improve the quality of the product.  
 
6 / EN  
Washing Machine / User’s Manual  
4.1 Installation  
• Apply to the nearest authorized service agent for the installation of your product.  
• Preparation of the location and electrical, tap water and waste water installations at the place of installation  
is under customer's responsibility.  
• Make sure that the water inlet and discharge hoses as well as the power cable are not folded, pinched or  
crushed while pushing the product into its place after installation or cleaning procedures.  
• Make sure that the installation and electrical connections of the product are performed by authorized  
service. Manufacturer shall not be held liable for damages that may arise from procedures carried out by  
unauthorized persons.  
• Prior to installation, visually check if the product has any defects on it. If so, do not have it installed.  
Damaged products cause risks for your safety.  
4.1.1 Appropriate installation location  
• Place the product on a hard and level floor. Do not put it onto a carpet with high pile or other similar  
surfaces.  
• When the washing machine and drier are placed on top of each other, their total weight –when loaded–  
amounts to 180 kilograms. Place the product on a solid and flat floor that has sufficient load carrying  
capacity!  
• Do not place the product on the power cable.  
• Do not install the product in the environments where the temperature falls below 0 ºC.  
• Leave a minimum space of 1 cm between the machine and the furniture.  
• On a graduated floor, do not place the product next to the edge or on a platform.  
4.1.2 Removing packaging reinforcement  
Tilt the machine backwards to remove the packaging reinforcement.  
Remove the packaging reinforcement by pulling the ribbon. Do not make  
this operation alone by yourself.  
4.1.3 Removing the transportation locks  
1
2
3
Loose all bolts with an appropriate wrench until they turn freely (C).  
Remove the transport safety bolts by turning them slightly.  
Insert the plastic covers in the bag containing the user manual to the openings on the rear panel. (P)  
CAUTION: Remove the transportation safety bolts before operating the washing machine! Otherwise, the product will be  
damaged.  
A
C
Keep the transportation safety bolts in a safe place to reuse when the washing machine needs to be moved again in the  
future.  
Install the transport safety bolts in reverse order of the disassembly procedure.  
Never move the product without the transportation safety bolts properly fixed in place!  
 
7 / EN  
Washing Machine / User’s Manual  
4.1.4 Connecting water supply  
The water supply pressure required to run the product is between 1 to 10 bars (0.1 – 1 MPa). It is necessary to have  
10 – 80 liters of water flowing from the fully open tap in one minute to have your machine run smoothly. Attach a pressure  
reducing valve if water pressure is higher.  
C
If you are going to use the double water-inlet product as a single (cold) water-inlet unit, you must install the supplied stopper  
to the hot water valve before operating the product. (Applies for the products supplied with a blind stopper group.)  
CAUTION: Models with a single water inlet should not be connected to the hot water tap. In such a case the laundry will  
get damaged or the product will switch to protection mode and will not operate.  
A
CAUTION: Do not use old or used water inlet hoses on the new product. It may cause stains on your laundry.  
Connect the special water supply hoses supplied with the product to the water inlets on the  
product. Red hose (left) (max. 90 ºC) is for hot water inlet, blue hose (right) (max. 25 ºC) is  
for cold water inlet.  
Make sure that the hot and cold water taps are connected correctly when the product is  
being installed. Otherwise, your laundry will come out hot at the end of the washing process  
and wear out.  
1
2
Tighten the nuts of the hose by hand. Never use a tool when  
tightening the nuts.  
When hose connection is completed, check whether there is leak  
problems at the connection points by opening the taps fully. If any  
leaks occur, turn off the tap and remove the nut. Retighten the nut  
carefully after checking the seal. In order to prevent the water leaks  
and resultant damages, keep the taps closed when you do not use  
the product.  
4.1.5 Connecting the drain hose to the drain  
• Attach the end of the drain hose directly to waste water drain, lavatory or bathtub.  
CAUTION: Your drain house will be flooded if the hose comes out of its housing during water discharge. Moreover, there  
is risk of scalding due to high washing temperatures! In order to prevent such situations and make sure that the machine  
performs water intake and discharge processes without any problem, fix the drain hose securely.  
A
• Connect the drain hose to a minimum height of 40 cm  
and a maximum height of 100 cm.  
• In case the drain hose is elevated after laying it on the  
floor level or close to the ground (less than 40 cm above  
the ground), water discharge becomes more difficult and  
the laundry may come out excessively wet. Therefore,  
follow the heights described in the figure.  
• To prevent the waste water to go back into the machine again and to ensure easy drainage, do not immerse  
the end of the hose into the waste water or do not insert it into the drain for more than 15 cm. If it is too  
long, cut it short.  
• The end of the hose should not be bent, it should not be stepped on and the hose must not be pinched  
between the drain and the machine.  
• If the length of the hose is too short, use it by adding an original extension hose. Length of the hose may  
not be longer than 3.2 m. To avoid water leak failures, the connection between the extension hose and the  
drain hose of the product must be fitted well with an appropriate clamp as not to come off and leak.  
 
8 / EN  
Washing Machine / User’s Manual  
4.1.6 Adjusting the feet  
CAUTION: In order to ensure that the product operates more silently and vibration-free, it must stand level and balanced  
on its feet. Balance the machine by adjusting the feet. Otherwise, the product may move from its place and cause crushing  
and vibration problems.  
A
CAUTION: Do not use any tools to loosen the lock nuts. Otherwise, they will get damaged.  
1
2
Loosen the lock nuts on the feet by hand.  
Adjust the feet until the product stands in a stable and balanced way.  
3. Tighten all lock nuts by hand again.  
4.1.7 Electrical connection  
Connect the product to a grounded outlet protected by a 16 A fuse. Our company shall not be liable for any  
damages that will arise when the product is used without grounding in accordance with the local regulations.  
• Connection must comply with national regulations.  
• Power cable plug must be within easy reach after installation.  
• If the current value of the fuse or breaker in the house is less than 16 Amps, have a qualified electrician  
install a 16 Amp fuse.  
• The voltage specified in the "Technical specifications" section must be equal to your mains voltage.  
• Do not make connections via extension cables or multi-plugs.  
CAUTION: Damaged power cables must be replaced by the Authorized Service Agents.  
B
4.1.8 Initial use  
Before starting to use the product make sure that the preparations are  
made which are in line with the “Important Safety and Environment  
Instructions” and the instructions in the “Installation” section.  
To prepare the product for washing laundry, perform first operation  
in Drum Cleaning programme. If this program is not available in your  
machine, apply the method which is described in the section 4.4.2.  
Use an anti-limescale suitable for the washing machines.  
Some water might have remained in the product due to the quality control processes in the production. It is not harmful for  
the product.  
C
 
9 / EN  
Washing Machine / User’s Manual  
4.2 Preparation  
4.2.1 Sorting the laundry  
* Sort laundry according to type of fabric, color, and degree of soiling and allowable water temperature.  
* Always obey the instructions given on the garment tags.  
4.2.2 Preparing laundry for washing  
• Laundry items with metal attachments such as, underwired bras, belt buckles or metal buttons will damage  
the machine. Remove the metal pieces or wash the clothes by putting them in a laundry bag or pillow case.  
• Take out all substances in the pockets such as coins, pens and paper clips, and turn pockets inside out and  
brush. Such objects may damage the product or cause noise problem.  
• Put small size clothes such as infant's socks and nylon stockings in a laundry bag or pillow case.  
• Place curtains in without compressing them. Remove curtain attachment items.  
• Fasten zippers, sew loose buttons and mend rips and tears.  
• Wash “machine washable” or “hand washable” labeled products only with an appropriate programme.  
• Do not wash colours and whites together. New, dark coloured cottons release a lot of dye. Wash them  
separately.  
• Tough stains must be treated properly before washing. If unsure, check with a dry cleaner.  
• Only use the dyes / color changers and descaling agents which are appropriate to machine wash. Always  
follow the instructions on the package.  
• Wash trousers and delicate laundry turned inside out.  
• Keep laundry items made of Angora wool in the freezer for a few hours before washing. This will reduce  
pilling.  
• Laundry that are subjected to materials such as flour, lime dust, milk powder, etc. intensely must be shaken  
off before placing into the machine. Such dusts and powders on the laundry may build up on the inner parts  
of the machine in time and can cause damage.  
4.2.3 Things to be done for energy saving  
Following information will help you use the product in an ecological and energy-efficient manner.  
• Operate the product in the highest capacity allowed by the programme you have selected, but do not  
overload; see, "Programme and consumption table". See, “Programme and consumption table"  
• Always follow the instructions on the detergent packaging.  
• Wash slightly soiled laundry at low temperatures.  
• Use faster programmes for small quantities of lightly soiled laundry.  
• Do not use prewash and high temperatures for laundry that is not heavily soiled or stained.  
• If you plan to dry your laundry in a dryer, select the highest spin speed recommended during washing  
process.  
• Do not use more detergent than the recommended amount specified on its package.  
4.2.4 Loading the laundry  
1. Open the laundry cover.  
2. Put the laundry items into the machine in a loose manner.  
3. Push and close the loading cover until you hear the locking sound. Ensure that no items are caught in the  
door. The loading door is locked while a programme is running. The door can only be opened a while after  
the programme comes to an end.  
4.2.5 Correct load capacity  
The maximum load capacity depends on the type of laundry, the degree of soiling and the washing  
programme desired.  
Machine automatically adjusts the water amount according to the weight of the laundry put inside it.  
WARNING: Follow the information in the “Programme and consumption table”. When overloaded, machine's washing  
performance will drop. Moreover, noise and vibration problems may occur.  
A
 
10 / EN  
Washing Machine / User’s Manual  
4.2.6 Using detergent and softener  
When using detergent, softener, starch, fabric dye, bleacher and decolorant, descaling agents; read the manufacturer's  
instructions written on the package and follow the dosages specified. Use measuring cup if available.  
C
2
1
3
The detergent drawer is composed of three compartments:  
– (1) for prewash  
– (2) for main wash  
– (3) for softener  
– ( ) in addition, there is a siphon piece in the softener compartment.  
Detergent, softener and other cleaning agents  
• Add detergent and softener before starting the washing programme.  
• While the washing cycle is in progress, do not leave the detergent dispenser open!  
• When using a programme without prewash, do not put any detergent into the prewash compartment  
(compartment nr. "1").  
• In a programme with prewash, do not put liquid detergent into the prewash compartment (compartment nr.  
"1").  
• Do not select a programme with prewash if you are using a detergent bag or dispensing ball. Place the  
detergent bag or the dispensing ball directly among the laundry in the machine.  
If you are using liquid detergent, do not forget to place the liquid detergent container into the main wash  
compartment (compartment number “2”).  
Choosing the detergent type  
Detergent type to be used depends on the fabric type and color.  
• Use different detergents for coloured and white laundry.  
• Wash your delicate clothes only with special detergents (liquid detergent, wool shampoo, etc.) used solely  
for delicate clothes.  
• When washing dark coloured clothes and quilts, it is recommended to use liquid detergent.  
• Wash woolens with special detergent made specifically for woolens.  
CAUTION: Use only detergents manufactured specifically for washing machines.  
A
CAUTION: Do not use soap powder.  
Adjusting detergent amount  
The amount of washing detergent to be used depends on the amount of laundry, the degree of soiling and  
water hardness.  
• Do not use amounts exceeding the dosage quantities recommended on the detergent package to avoid  
problems of excessive foam, poor rinsing, financial savings and finally, environmental protection.  
• Use lesser detergent for small amounts or lightly soiled clothes.  
Using softeners  
Pour the softener into the softener compartment of the detergent drawer.  
• Do not exceed the (>max<) level sign on the softener compartment.  
• If the softener has lost its fluidity, dilute it with water before putting it in the detergent drawer.  
Using liquid detergents  
If the product contains a liquid detergent cup:  
Put the liquid detergent container into the  
compartment no “2”.  
If the liquid detergent lost its fluidity, dilute it  
with water before putting it into the detergent  
container.  
 
Washing Machine / User’s Manual  
11 / EN  
If the product does not contain a liquid detergent cup:  
• Do not use liquid detergent for the prewash in a programme with prewash.  
• Liquid detergent stains your clothes when used with Delayed Start function. If you are going to use the  
Delayed Start function, do not use liquid detergent.  
Using gel and tablet detergent  
• If the gel detergent thickness is fluidal and your machine does not contain a special liquid detergent cup,  
put the gel detergent into the main wash detergent compartment during first water intake. If your machine  
contains a liquid detergent cup, fill the detergent into this cup before starting the programme.  
• If the gel detergent thickness is not fluidal or in the shape of capsule liquid tablet, put it directly into the  
drum before washing.  
• Put tablet detergents into the main wash compartment (compartment nr. "2") or directly into the drum  
before washing.  
Using starch  
• Put the liquid soda, powder soda or the fabric dye into the softener compartment.  
Do not use softener and starch together in a washing cycle.  
Wipe the inside of the machine with a damp and clean cloth after using starch.  
Using limescale remover  
• When required, use limescale removers manufactured specifically for washing machines only.  
Using bleaches  
Add the bleach at the beginning of the washing cycle by selecting a prewash program. Do not put detergent  
in the prewash compartment. As an alternative application, select a programme with extra rinse and add  
the bleaching agent while the machine is taking water from the detergent compartment during first rinsing  
step.  
• Do not use bleaching agent and detergent by mixing them.  
• Use just a little amount (approx. 50 ml) of bleaching agent and rinse the clothes very well as it causes skin  
irritation. Do not pour the bleach onto the laundry and do not use it with the colored items.  
• When using oxygen-based decolorant, select a program which washes the laundry at a low temperature.  
• Oxygen-based decolorant can be used with the detergent; however, if it is not at the same consistence, first  
put detergent in the compartment number “2” in the detergent dispenser and wait for the machine to flush  
the detergent when taking in water. While the machine continues taking in water, add decolorant in the  
same compartment.  
 
12 / EN  
Washing Machine / User’s Manual  
4.2.7 Tips for efficient washing  
Clothes  
Light Colours and  
Whites  
Black/Dark  
Colours  
Delicates/  
Woolens/Silks  
(Recommended  
Colours  
(Recommended  
(Recommended temperature  
(Recommended temperature range temperature range based temperature range  
range based on soiling level:  
o
o
based on soiling level: cold -40 C) on soiling level: cold  
based on soiling  
40-90 C)  
o
o
-40 C)  
level: cold -30 C)  
It may be necessary to pre-treat  
the stains or perform prewash.  
Powder and liquid detergents  
recommended for whites can be  
Powder and liquid detergents  
recommended for colors can be  
Heavily  
Soiled  
Prefer liquid  
Liquid detergents  
used at dosages recommended  
suitable for colors  
detergents produced  
for delicate clothes.  
Woolen and silk  
clothes must be  
washed with special  
woolen detergents.  
for heavily soiled clothes. It is  
and dark colors can  
used at dosages recommended  
recommended to use powder  
be used at dosages  
(difficult stains  
such as grass,  
coffee, fruits and  
blood.)  
for heavily soiled clothes. It is  
recommended to use powder  
detergents to clean clay and soil  
stains and the stains that are  
sensitive to bleaches.  
detergents to clean clay and  
recommended for heavily  
soil stains and the stains that  
soiled clothes.  
are sensitive to bleaches. Use  
detergents without bleach.  
Prefer liquid  
Normally  
Powder and liquid detergents  
recommended for colors can be  
recommended for whites can be used at dosages recommended for and dark colors can  
Liquid detergents  
suitable for colors  
detergents produced  
for delicate clothes.  
Woolen and silk  
clothes must be  
washed with special  
woolen detergents.  
Powder and liquid detergents  
Soiled  
(For example,  
stains caused by  
body on collars  
and cuffs)  
used at dosages recommended  
for normally soiled clothes.  
normally soiled clothes. Detergents be used at dosages  
which do not contain bleach should recommended for  
be used.  
normally soiled clothes.  
Prefer liquid  
Powder and liquid detergents  
recommended for colors can be  
recommended for whites can be used at dosages recommended for and dark colors can  
Liquid detergents  
suitable for colors  
Lightly  
Soiled  
detergents produced  
for delicate clothes.  
Woolen and silk  
clothes must be  
washed with special  
woolen detergents.  
Powder and liquid detergents  
used at dosages recommended  
for lightly soiled clothes.  
lightly soiled clothes. Detergents  
which do not contain bleach should recommended for lightly  
be used. soiled clothes.  
be used at dosages  
(No visible stains  
exist.)  
 
Washing Machine / User’s Manual  
13 / EN  
4.3 Operating the product  
4.3.1 Control panel  
1
2
3
4
5
6
7
8
9
14  
13  
12  
11  
10  
1 - Programme selection knob  
2 - Temperature selection LEDs  
3 - Spin speed selection LEDs  
4 - Duration information display  
5 - Child lock enabled LED  
6 - End Time Setting button  
7 - Door lock enabled LED  
8 - Programme follow-up indicator LEDs  
9 - On / Off button  
10 - Start / Pause button  
11 - Auxiliary function buttons  
12 - Spin speed adjustment button  
13 - Temperature adjustment button  
14 - Programme Selection LEDs  
 
Washing Machine / User’s Manual  
14 / EN  
4.3.2 Programme selection  
1 Determine the programme suitable for the type, quantity and soiling level of the laundry in accordance with  
the "Programme and consumption table".  
1 Select the desired programme with the “Programme Selection” knob.  
Programmes are limited with the highest spin speed appropriate for that particular type of fabric.  
When selecting the program you will use, always take fabric type, color, soil degree and permitted water temperature into  
consideration.  
C
Always prefer the lowest temperature value which is fit to your laundry type. Higher temperature means higher power  
consumption.  
4.3.3 Programmes  
• Cottons  
Use this programme for your durable whites and colourfast cotton clothes. This programme is suggested for  
washing heavily soiled items.  
• Synthetics  
Use to wash your synthetic clothes (shirts, blouses, synthetic/cotton blends, etc.). It washes with a gentle  
action and has a shorter washing cycle compared to the Cottons programme.  
For curtains and tulle, use the Synthetic 40˚C programme with prewash and anti-creasing functions selected.  
As their meshed texture causes excessive foaming, wash the veils/tulle by putting little amount of detergent  
into the main wash compartment. Do not put detergent in the prewash compartment.  
• Wool  
Use to wash your woolen clothes. Select the appropriate temperature complying with the tags of your clothes.  
Use appropriate detergents for woolens.  
“The wool wash cycle of this machine has been approved by The Woolmark Company for the washing of machine washable  
wool products provided that the products are washed according to the instructions on the garment label and those issued by  
the manufacturer of this washing machine. M14069.”  
“In UK, Eire, Hong Kong and India the Woolmark trade mark is a Certification trade mark.”  
• Cottons Eco  
Use to wash your normally soiled, durable cotton and linen laundry. Although it washes longer than all other  
programmes, it provides high energy and water savings. Actual water temperature may be different from the  
stated wash temperature. When you load the machine with less laundry (e.g. ½ capacity or less), programme  
time may automatically get shorter. In this case, energy and water consumption will decrease more, providing  
a more economic wash. This programme is available in the models with the remaining time indicator.  
• Anti-Allergy+  
Use this programme for your laundry for which you require an anti-allergic and hygienic washing at high  
temperature with intensive and long washing cycle.  
• Gentle Care 20°  
Use it to wash your delicate laundry. It washes with a gentler action without any interim spins compared to the  
Synthetics program. It should be used for laundry for which sensitive wash is recommended.  
• Hand wash  
Use to wash your woolen/delicate clothes that bear “not machine-washable” tags and for which hand wash is  
recommended. It washes laundry with a very gentle washing action to not to damage clothes.  
• Daily/Quick  
Use this programme to wash your lightly soiled cotton clothes in a short time.  
•Quick 14’  
Use to wash your lightly soiled and unstained cotton laundry in a short time.  
• Darkcare  
Use this programme to wash your dark colored laundry or colored laundry that you do not want them get  
faded. Washing is performed with little mechanic action and at low temperatures. It is recommended to use  
liquid detergent or woolen shampoo for dark coloured laundry.  
 
15 / EN  
Washing Machine / User’s Manual  
• Mix 40  
Use this programme to wash your cotton and synthetic clothes together without sorting them.  
• Aqua 40’ 40°  
Use this programme to wash your lightly soiled and unstained cotton laundry in a short time.  
• Sports & Outdoor  
Use this programme to wash your garments that are worn for a short time such as sportswear. It is suitable to  
wash little amount of cotton / synthetic blended garments.  
• Hygiene 20°  
Use this programme for your laundry for which you require washing at lower temperature with intensive and  
long washing cycle. Use this programme for your laundry for which you require hygienic washing at lower  
temperature.  
• Rinse  
Use when you want to rinse or starch separately.  
• Spin + Drain  
Use to drain the water in the machine.  
4.3.4 Temperature selection  
Whenever a new programme is selected, the recommended temperature for the selected programme appears  
on the temperature indicator.  
To decrease the temperature, press the Temperature Adjustment button. Temperature will decrease gradually.  
If the programme has not reached the heating step, you can change the temperature without switching the machine to  
Pause mode.  
C
4.3.5 Spin speed selection  
Whenever a new programme is selected, the recommended spin speed of the selected programme is  
displayed on the spin speed indicator.  
To decrease the spin speed, press the Spin Speed Adjustment button. Spin speed decreases gradually.  
Then, depending on the model of the product, "Rinse Hold" and "No Spin" options appear on the display. See  
"Auxiliary function selection" section for explanations of these options.  
If the programme has not reached the spinning step, you can change the speed without switching the machine to Pause  
mode.  
C
Indicative values for Synthetics programmes (EN)  
Remaining Moisture  
Content (%) **  
Remaining Moisture  
Content (%) **  
≤ 1000 rpm  
> 1000 rpm  
Synthetics 60  
Synthetics 40  
105l/135l  
105l/135l  
45  
45  
40  
40  
3
3
52  
48  
1.20  
0.83  
* You can see the washing time of the programme you have selected on the display of the machine. It is normal that  
small differences may occur between the time shown on the display and the real washing time.  
** Remaining moisture content values may differ according to the selected spin speed.  
 
16 / EN  
Washing Machine / User’s Manual  
4.3.6 Programme and consumption table  
EN  
Auxiliary functions  
2
Selectable temperature  
range °C  
Programme (°C)  
Cottons Eco  
Cottons  
40**  
90  
60  
40  
60  
40  
40  
30  
60  
40  
40  
40  
40  
20  
20  
30  
90  
60  
30  
7
7
1600  
1600  
1600  
1600  
1200  
1200  
1200  
1200  
1600  
1000  
1000  
1000  
1400  
1200  
1600  
1400  
1400  
1400  
1400  
Cold-40  
Cold-90  
Cold-90  
Cold-90  
Cold-60  
Cold-60  
Cold-40  
Cold-30  
30-90  
64  
64  
60  
52  
48  
43  
37  
88  
73  
63  
32  
45  
45  
82  
33  
57  
57  
54  
2.30  
1.68  
0.91  
1.20  
0.83  
0.20  
0.15  
1.90  
0.70  
0.70  
0.40  
0.60  
0.15  
0.42  
0.10  
1.95  
1.10  
0.20  
7
8
3
Synthetics  
3
Wool  
1.5  
1
Hand wash  
Anti-Allergy+  
Darkcare  
7
3
Cold-40  
Cold-40  
Cold-40  
Cold-40  
20  
Sports & Outdoor  
Mix 40  
3.5  
3.5  
7
Aqua 40’ 40°  
Gentle Care 20°  
Hygiene 20°  
Quick 14’  
3.5  
4
20  
2
Cold-30  
Cold-90  
Cold-90  
Cold-90  
7
Daily/Quick  
7
7
*
**  
: Selectable.  
: Automatically selected, no canceling.  
: Energy Label programme (AS/NZS 2040)  
*** : If maximum spin speed of the machine is lower then this value, you can only select up to the maximum spin speed.  
**** : Programme detects the type and quantity of the laundry to automatically adjust water and energy consumption and  
programme time.  
-
: See the programme description for maximum load.  
The auxiliary functions in the table may vary according to the model of your machine.  
Water and power consumption may vary subject to the changes in water pressure, water  
hardness and temperature, ambient temperature, type and amount of laundry, selection of  
auxiliary functions and spin speed, and changes in electric voltage.  
C
You can see the washing time of the programme you have selected on the display of the  
machine. It is normal that small differences may occur between the time shown on the display  
and the real washing time.  
“Selection patterns for auxiliary functions can be changed by the manufacturer company. New  
selection patterns can be added or removed.”  
“The spin speed of your machine may vary according to the programme; this spin speed cannot  
exceed the max. spin speed of your machine.”  
 
17 / EN  
Washing Machine / User’s Manual  
4.3.7 Auxiliary function selection  
Select the desired auxiliary functions before starting the programme.  
Whenever a programme is selected, if a relevant auxiliary function is selected its related indicator light will  
illuminate.  
Indicator lights of the auxiliary functions that are not allowed to be selected with the current programme will flash and an  
audio warning is given.  
C
Furthermore, you may also select or cancel auxiliary functions that are suitable to the running programme  
after the washing cycle starts. If the wash cycle has reached a point where no auxiliary function can be  
selected, an audio warning will be given and the related auxiliary function's light will flash.  
Some functions cannot be selected together. If a second auxiliary function conflicting with the first one is selected before  
starting the machine, the function selected first will be canceled and the second auxiliary function selection will remain  
active. For example, if you want to select Quick Wash after you have selected the Additional Water, Additional Water will be  
canceled and Quick Wash will remain active.  
C
An auxiliary function that is not compatible with the programme cannot be selected. (See, “Programme and consumption  
table")  
Some programmes have auxiliary functions that must be operated simultaneously. Those functions cannot be cancelled. The  
frame of the auxiliary function will not be illuminated, only inner area will be illuminated.  
• Prewash  
A Prewash is only worthwhile for heavily soiled laundry. Not using the Prewash will save energy, water,  
detergent and time.  
• Quick  
This function can be used in Cottons and Synthetics programmes. It decreases the washing times and also the  
number of rinsing steps for lightly soiled laundry.  
When you select this function, load your machine with half of the maximum laundry specified in the programme table.  
C
• Rinse Plus  
This function enables the machine to make another rinsing in addition to the one already made after the main  
wash. Thus, the risk for sensitive skins (babies, allergic skins, etc.) to be effected by the minimal detergent  
remnants on the laundry can be reduced.  
• Anti-Creasing  
This function creases the clothes lesser when they are being washed. Drum movement is reduced and spin  
speed is limited to prevent creasing. In addition, washing is done with a higher water level.  
• Rinse Hold  
If you are not going to unload your clothes immediately after the programme completes, you can use rinse  
hold function to keep your laundry in the final rinsing water in order to prevent them from getting wrinkled  
when there is no water in the machine. Press Start / Pause button after this process if you want to drain the  
water without spinning your laundry. Programme will resume and complete after draining the water.  
If you want to spin the laundry held in water, adjust the Spin Speed and press Start / Pause button.  
The programme resumes. Water is drained, laundry is spun and the programme is completed.  
• Night Mode  
Use to wash the cottons with lesser energy consumption and silently. Spin steps are cancelled for a silent  
washing and the cycle ends with the Rinse Hold step. After completion of the programme, run Spin cycle to  
spin the laundry.  
• Pet hair removal  
This function helps to remove pet hair that remain on your garments more effectively.  
When you select this function, Prewash and Extra Rinse steps are added to the normal programme. Thus,  
washing is performed with more water (30%) and the pet hair is removed more effectively.  
WARNING: Never wash your pets in the washing machine.  
A
 
18 / EN  
Washing Machine / User’s Manual  
4.3.8 End Time  
With the End Time function, the startup of the programme may be delayed up to 24 hours. After pressing  
End Time button, the programme's estimated ending time is displayed. If the End Time is adjusted, End Time  
indicator is illuminated.  
In order for the End Time function to be activated and the programme to be completed at the end of the  
specified time, you must press Start / Pause button after adjusting the time.  
If you want to cancel End Time function, press On / Off button to turn off and on the machine.  
Do not use liquid detergents when you activate End Time function! There is the risk of staining of the clothes.  
C
1 Open the loading door, place the laundry and put detergent, etc.  
2 Select the washing programme, temperature, spin speed and, if required, the auxiliary functions.  
3 Set the end time of your choice by pressing the End Time button. End Time indicator illuminates.  
4 Press Start / Pause button. Time countdown starts. “:” sign in the middle of the end time on the display  
starts flashing.  
Additional laundry may be loaded during the End Time countdown period. At the end of the countdown, End Time indicator  
turns off, washing cycle starts and the time of the selected programme appears on the display.  
C
When the End Time selection is completed, the time appears on the screen consists of end time plus the duration of the  
selected programme.  
4.3.9 Starting the programme  
1. Press Start / Pause button to start the programme.  
2. Programme follow-up light showing the startup of the programme will turn on.  
If no programme is started or no key is pressed within 1-10 minute during programme selection process, the machine will  
switch to OFF mode. Display and all indicators are turned off.  
Selected programme data will be displayed if you press On / Off button.  
C
4.3.10 Loading door lock  
There is a locking system on the loading door of the machine that prevents opening of the door in cases when  
the water level is unsuitable.  
"Door Locked" LED in the panel turns on when the loading door is locked.  
4.3.11 Changing the selections after the programme has started  
After the programme has started you can make the following changes.  
4.3.11.1 Switching the machine to pause mode:  
Press the Start/Pause button to switch the machine to pause mode while a programme is running. The light  
indicating the Start/Pause status and programme step starts flashing on the Programme Follow-up indicator  
to show that the machine has been switched to the pause mode. Also, Loading Door light will also flash until  
the door is ready to be opened. When the loading door is ready to be opened loading door light will will turn off  
and programme step indicator and Start / Stop LED continue to flash.  
Also, when the loading door is ready to be opened, Loading Door light will also turn off in addition to the  
programme step light.  
4.3.11.2 Changing the auxiliary function, speed and temperature  
Depending on the step the programme has reached, you can cancel or select the auxiliary functions. See,  
"Auxiliary function selection".  
You can also change the speed and temperature settings. See, "Spin speed selection" and "Temperature  
selection".  
If no change is allowed, the relevant light will flash for 3 times.  
C
 
19 / EN  
Washing Machine / User’s Manual  
4.3.11.3 Adding or taking out laundry  
1. Press the Start / Pause button to switch the machine to pause mode. The programme follow-up light of the  
relevant step during which the machine was switched into the pause mode will flash.  
2. Wait until the Loading Door can be opened.  
3. Open the Loading Door and add or take out the laundry.  
5. Close the Loading Door.  
6. Make changes in auxiliary functions, temperature and speed settings if necessary.  
7. Press Start/Pause button to start the machine.  
4.3.12 Child Lock  
Use Child Lock function to prevent children from tampering with the machine. Thus you can avoid any changes  
in a running programme.  
You can switch on and off the machine with On / Off button when the Child Lock is active. When you switch on the  
machine again, programme will resume from where it has stopped.  
C
4.3.12.1 To activate the child lock:  
Press and hold Auxiliary Function button 2 for 3 seconds. In the programme selection display on the panel,  
"Child lock enabled" light will turn on. You can release Auxiliary Function button 2 when this warning is  
displayed.  
4.3.12.2 To deactivate the child lock:  
Press and hold Auxiliary Function button 2 for 3 seconds. In the programme selection display on the panel,  
"Child lock enabled" light will turn off.  
4.3.13 Canceling the programme  
The programme is cancelled when the machine is turned off and on again. Press and hold On / Off button for  
3 seconds.  
If you press On / Off button when the Child Lock is enabled, the programme will not be cancelled. You should cancel the  
Child Lock first.  
C
If you want to open the loading door after you have cancelled the programme but it is not possible to open the loading door  
since the water level in the machine is above the loading door opening, then turn the Programme Selection knob to  
Pump+Spin programme and discharge the water in the machine.  
4.3.14 End of programme  
End LED appears on the display when the programme is completed.  
If you do not press any button for 10 minutes, the machine will switch to OFF mode. Display and all indicators  
are turned off.  
Completed programme steps will be displayed if you press On / Off button.  
4.3.15 Your machine features "Standby Mode".  
After you switch on your machine with On-Off button, if no program is started or no other procedure is  
performed at the selection step or no action is taken within approx. 10 minutes after the selected program  
ends, your machine will switch to OFF mode automatically. Display and all indicators are turned off. Selected  
programme data will be displayed if you press On / Off button. Before you start the program, check the  
accuracy of your selections. If necessary, repeat them. This is not an error.  
 
20 / EN  
Washing Machine / User’s Manual  
4.4 Maintenance and cleaning  
Service life of product extends and frequently experienced problems will be reduced if it is cleaned at regular  
intervals.  
4.4.1 Cleaning the detergent drawer  
Clean the detergent drawer at regular intervals (every 4-5 washing cycles) as  
shown below in order to prevent accumulation of powder detergent in time.  
Lift the rear part of the siphon to remove it as illustrated.  
If more than normal amount of water and softener mixture starts to gather in the  
softener compartment, the siphon must be cleaned.  
1
Press the dotted point on the siphon in the softener compartment and pull towards you until the  
compartment is removed from the machine.  
2. Wash the detergent drawer and the siphon with plenty of lukewarm water in a washbasin. In order to  
prevent the residues to contact your skin, clean it with an appropriate brush by wearing a pair of gloves.  
3
Insert the drawer back into its place after cleaning and make sure that it is seated well.  
4.4.2 Cleaning the loading door and the drum  
For products with drum cleaning programme, please see Operating the product - Programmes.  
For products without drum cleaning, follow the below steps to clean the drum:  
Select Additional Water or Extra Rinse auxiliary functions. Use a Cottons programme without pre-wash.  
Set the temperature to the level recommended on the drum cleaning agent which can be provided  
from authorized services. Apply this procedure without any laundry in the product. Before starting the  
programme, put 1 pouch of special drum cleaning agent (if the special agent could not be supplied, put max.  
100 g of powder anti-limescale) into the main wash detergent compartment (compartment no. „2“). If the anti-  
limescale is in tablet form, put only one tablet into the main wash compartment no. „2“. Dry the inside of the  
bellow with a clean piece of cloth after the programme has come to an end.  
Repeat Drum Cleaning process in every 2 months.  
Use an anti-limescale suitable for the washing machines.  
C
After every washing make sure that no foreign substance is left in the drum.  
If the holes on the bellow shown in the figure is blocked, open the holes using a  
toothpick.  
Foreign metal substances will cause rust stains in the drum. Clean the stains on the  
drum surface by using cleaning agents for stainless steel.  
Never use steel wool or wire wool. These will damage the painted, chromated and  
plastic surfaces.  
 
21 / EN  
Washing Machine / User’s Manual  
4.4.3 Cleaning the body and control panel  
Wipe the body of the machine with soapy water or non-corrosive mild gel detergents as necessary, and dry  
with a soft cloth.  
Use only a soft and damp cloth to clean the control panel.  
4.4.4 Cleaning the water intake filters  
There is a filter at the end of each water intake valve at the rear of the machine and also at the end of each  
water intake hose where they are connected to the tap. These filters prevent foreign substances and dirt in  
the water to enter the washing machine. Filters should be cleaned as they do get dirty.  
1. Close the taps.  
2. Remove the nuts of the water intake hoses to access  
the filters on the water intake valves. Clean them with an  
appropriate brush. If the filters are too dirty, remove them  
from their places with a pliers and clean in this way.  
3. Take out the filters on the flat ends of the water intake  
hoses together with the gaskets and clean thoroughly  
under running water.  
4. Replace the seals and filters carefully and tighten their  
nuts by hand.  
4.4.5 Draining remaining water and cleaning the pump filter  
The filter system in your machine prevents solid items such as buttons, coins and fabric fibers clogging the  
pump impeller during discharge of washing water. Thus, the water will be discharged without any problem and  
the service life of the pump will extend.  
If the machine fails to drain water, the pump filter is clogged. Filter must be cleaned whenever it is clogged or  
in every 3 months. Water must be drained off first to clean the pump filter.  
In addition, prior to transporting the machine (e.g., when moving to another house) and in case of freezing of  
the water, water may have to be drained completely.  
CAUTION: Foreign substances left in the pump filter may damage your machine or may cause noise problem.  
A
CAUTION: If the product is not being used, shut the tap shut, remove mains pipe and drain the water inside the machine  
against any likely freezing.  
CAUTION: After each use, turn off the water tap to which the mains hose is connected.  
In order to clean the dirty filter and discharge the water:  
1 Unplug the machine to cut off the supply power.  
CAUTION: Temperature of the water inside the machine may rise up to 90 ºC. To avoid the burning risk, clean the filter  
after the water inside the machine is cooled down.  
A
2. Open the filter cover.  
3 Follow the below procedures in order to drain water.  
If the product has an emergency water draining hose, in order to drain the water:  
a
b
Pull the emergency draining hose out from its seat  
Place a large container at the end of the hose. Drain  
the water into the container by pulling out the plug at  
the end of the hose. When the container is full, block  
the inlet of the hose by replacing the plug. After the  
container is emptied, repeat the above procedure to  
drain the water in the machine completely.  
c
d
When draining of water is finished, close the end by  
the plug again and fix the hose in its place.  
Turn and remove the pump filter.  
 
Washing Machine / User’s Manual  
22 / EN  
If the product does not have an emergency water drain hose, in order to drain the water:  
a. In order to collect the water to flow out of the filter,  
place a large vessel in front of the filter.  
b. Turn and loosen the pump filter until water starts to  
flow (counterclockwise). Fill the flowing water into  
the container you have placed in front of the filter.  
Always keep a piece of cloth handy to absorb any  
spilled water.  
c
When the water inside the machine is finished, take  
out the filter completely by turning it.  
4 Clean any residues inside the filter as well as fibers, if any, around the pump impeller region.  
5. Replace the filter.  
6. If the filter cap is composed of two pieces, close the filter cap by pressing on the tab. If it is one piece, seat  
the tabs in the lower part into their places first, and then press the upper part to close.  
 
23 / EN  
Washing Machine / User’s Manual  
5
Troubleshooting  
Problem  
Program does not start after  
closing the door.  
Reason  
Solution  
Š *Press the Start / Pause / Cancel button.  
Start / Pause / Cancel button was not pressed.  
Programme cannot be started or  
selected.  
Washing machine has switched to self protection  
mode due to a supply problem (line voltage, water  
pressure, etc.).  
Š Press and hold On / Off button for 3 seconds.  
(see. "Cancellation of program")  
Water in the machine.  
Some water might have remained in the product due Š This is not a failure; water is not harmful to the  
to the quality control processes in the production.  
machine.  
Machine does not fill with water.  
Tap is turned off.  
Water inlet hose is bent.  
Š Turn on the taps.  
Š Flatten the hose.  
Water inlet filter is clogged.  
Loading door may be open.  
Š Clean the filter.  
Š Close the door.  
Machine does not drain water.  
Water drain hose might be clogged or twisted.  
Pump filter is clogged.  
Š Clean or flatten the hose.  
Š Clean the pump filter.  
Š Adjust the feet to level the machine.  
Š Clean the pump filter.  
Machine vibrates or makes noise. Machine might be standing unbalanced.  
A hard substance might have entered into the pump  
filter.  
Transportation safety bolts are not removed.  
Laundry quantity in the machine might be too little.  
Machine might be overloaded with laundry.  
Š Remove the transportation safety bolts.  
Š Add more laundry to the machine.  
Š Take out some of the laundry from the machine  
or distribute the load by hand to balance it  
homogenously in the machine.  
Machine might be leaning on a rigid item.  
Š Make sure that the machine is not leaning on  
anything.  
There is water leaking from the  
bottom of the washing machine.  
Water drain hose might be clogged or twisted.  
Pump filter is clogged.  
Š Clean or flatten the hose.  
Š Clean the pump filter.  
Machine stopped shortly after the Machine might have stopped temporarily due to low  
Š It will resume running when the voltage restores to  
the normal level.  
programme started.  
voltage.  
Machine directly discharges the  
water it takes in.  
No water can be seen in the  
machine during washing.  
Loading door cannot be opened.  
Draining hose might not be at adequate height.  
Š Connect the water draining hose as described in  
the operation manual.  
Š This is not a failure.  
The water level is not visible from outside of the  
washing machine.  
Door lock is activated because of the water level in  
the machine.  
Š Drain the water by running the Pump or Spin  
programme.  
Machine is heating up the water or it is at the spinning Š Wait until the programme completes.  
cycle.  
Child lock is engaged. Door lock will be deactivated  
a couple of minutes after the programme has come  
to an end.  
Š Wait for a couple of minutes for deactivation of  
the door lock.  
Washing takes longer time than  
specified in the manual.(*)  
Water pressure is low.  
Š Machine waits until taking in adequate amount  
of water to prevent poor washing quality due to  
the decreased amount of water. Therefore, the  
washing time extends.  
Voltage might be low.  
Š Washing time is prolonged to avoid poor washing  
results when the supply voltage is low.  
Input temperature of water might be low.  
Š Required time to heat up the water extends in cold  
seasons. Also, washing time can be lengthened to  
avoid poor washing results.  
Number of rinses and/or amount of rinse water might Š Machine increases the amount of rinse water  
have increased.  
when good rinsing is needed and adds an extra  
rinsing step if necessary.  
Excessive foam might have occurred and automatic  
foam absorption system might have been activated  
due to too much detergent usage.  
Š Use recommended amount of detergent.  
 
Washing Machine / User’s Manual  
24 / EN  
Problem  
Programme time does not  
countdown. (On models with  
display) (*)  
Reason  
Timer may stop during water intake.  
Solution  
Š Timer indicator will not countdown until the  
machine takes in adequate amount of water. The  
machine will wait until there is sufficient amount  
of water to avoid poor washing results due to lack  
of water. Timer indicator will resume countdown  
after this.  
Timer may stop during heating step.  
Timer may stop during spinning step.  
Š Timer indicator will not countdown until the  
machine reaches the selected temperature.  
Š Automatic unbalanced load detection system  
might be activated due to the unbalanced  
distribution of the laundry in the drum.  
Programme time does not  
countdown. (*)  
There might be unbalanced load in the machine.  
There might be unbalanced load in the machine.  
Š Automatic unbalanced load detection system  
might be activated due to the unbalanced  
distribution of the laundry in the drum.  
Š Automatic unbalanced load detection system  
might be activated due to the unbalanced  
distribution of the laundry in the drum.  
Š Check the filter and the draining hose.  
Machine does not switch to  
spinning step. (*)  
The machine will not spin if water is not drained  
completely.  
Excessive foam might have occurred and automatic  
foam absorption system might have been activated  
due to too much detergent usage.  
Insufficient amount of detergent has been used over a Š Use the recommended amount of detergent  
long period of time.  
Washing was made at low temperatures for a long  
time.  
Š Use recommended amount of detergent.  
Washing performance is poor:  
Laundry turns gray. (**)  
appropriate for water hardness and the laundry.  
Š Select the proper temperature for the laundry to  
be washed.  
Insufficient amount of detergent is used with hard  
water.  
Š Using insufficient amount of detergent with hard  
water causes the soil to stick on the cloth and  
this turns the cloth into gray in time. It is difficult  
to eliminate graying once it happens. Use the  
recommended amount of detergent appropriate  
for water hardness and the laundry.  
Too much detergent is used.  
Š Use the recommended amount of detergent  
appropriate for water hardness and the laundry.  
Š Use the recommended amount of detergent  
appropriate for water hardness and the laundry.  
Š Do not load the machine in excess. Load with  
amounts recommended in the "Programme and  
consumption table".  
Washing performance is poor:  
Stains persist or the laundry is not  
whitened. (**)  
Insufficient amount of detergent is used.  
Excessive laundry was loaded in.  
Wrong programme and temperature were selected.  
Wrong type of detergent is used.  
Š Select the proper programme and temperature for  
the laundry to be washed.  
Š Use original detergent appropriate for the  
machine.  
Too much detergent is used.  
Š Put the detergent in the correct compartment. Do  
not mix the bleaching agent and the detergent  
with each other.  
Washing performance is poor: Oily Regular drum cleaning is not applied.  
stains appeared on the laundry. (**)  
Š Clean the drum regularly. For this, please see  
4.4.2.  
Washing performance is poor:  
Clothes smell unpleasantly. (**)  
Odours and bacteria layers are formed on the drum as Š Leave the detergent drawer as well as the loading  
a result of continuous washing at lower temperatures  
and/or in short programmes.  
door of the machine ajar after each washing.  
Thus, a humid environment favorable for bacteria  
cannot occur in the machine.  
Colour of the clothes faded. (**)  
Excessive laundry was loaded in.  
Detergent in use is damp.  
Š Do not load the machine in excess.  
Š Keep detergents closed in an environment free  
of humidity and do not expose them to excessive  
temperatures.  
A higher temperature is selected.  
Š Select the proper programme and temperature  
according to the type and soiling degree of the  
laundry.  
 
Washing Machine / User’s Manual  
25 / EN  
Problem  
It does not rinse well.  
Reason  
Solution  
The amount, brand and storage conditions of the  
detergent used are inappropriate.  
Š Use a detergent appropriate for the washing  
machine and your laundry. Keep detergents closed  
in an environment free of humidity and do not  
expose them to excessive temperatures.  
Š If detergent is put in the prewash compartment  
although prewash cycle is not selected, machine  
can take this detergent during rinsing or  
softener step. Put the detergent in the correct  
compartment.  
Detergent is put in the wrong compartment.  
Pump filter is clogged.  
Drain hose is folded.  
Š Check the filter.  
Š Check the drain hose.  
Laundry became stiff after  
washing. (**)  
Insufficient amount of detergent is used.  
Š Using insufficient amount of detergent for the  
water hardness can cause the laundry to become  
stiff in time. Use appropriate amount of detergent  
according to the water hardness.  
Detergent is put in the wrong compartment.  
Š If detergent is put in the prewash compartment  
although prewash cycle is not selected, machine  
can take this detergent during rinsing or  
softener step. Put the detergent in the correct  
compartment.  
Detergent might be mixed with the softener.  
Detergent is put in the wrong compartment.  
Š Do not mix the softener with detergent. Wash and  
clean the dispenser with hot water.  
Laundry does not smell like the  
softener. (**)  
Š If detergent is put in the prewash compartment  
although prewash cycle is not selected,  
machine can take this detergent during rinsing  
or softener step. Wash and clean the dispenser  
with hot water. Put the detergent in the correct  
compartment.  
Detergent might be mixed with the softener.  
Š Do not mix the softener with detergent. Wash and  
clean the dispenser with hot water.  
Detergent residue in the detergent Detergent is put in wet drawer.  
drawer. (**)  
Š Dry the detergent drawer before putting in  
detergent.  
Detergent has gotten damp.  
Š Keep detergents closed in an environment free  
of humidity and do not expose them to excessive  
temperatures.  
Water pressure is low.  
The detergent in the main wash compartment got  
Š Check the water pressure.  
Š Check the holes and clean if they are clogged.  
wet while taking in the prewash water. Holes of the  
detergent compartment are blocked.  
There is a problem with the detergent drawer valves. Š Call the Authorized Service Agent.  
Detergent might be mixed with the softener.  
Regular drum cleaning is not applied.  
Š Do not mix the softener with detergent. Wash and  
clean the dispenser with hot water.  
Š Clean the drum regularly. For this, please see  
4.4.2.  
Too much foam forms in the  
machine. (**)  
Improper detergents for the washing machine are  
being used.  
Excessive amount of detergent is used.  
Detergent was stored under improper conditions.  
Š Use detergents appropriate for the washing  
machine.  
Š Use only sufficient amount of detergent.  
Š Store detergent in a closed and dry location. Do  
not store in excessively hot places.  
Some meshed laundry such as tulle may foam too  
much because of their texture.  
Detergent is put in the wrong compartment.  
Softener is being taken early.  
Š Use smaller amounts of detergent for this type  
of item.  
Š Put the detergent in the correct compartment.  
Š There may be problem in the valves or in the  
detergent dispenser. Call the Authorized Service  
Agent.  
Foam is overflowing from the  
detergent drawer.  
Too much detergent is used.  
Š Mix 1 tablespoonful softener and ½ l water and  
pour into the main wash compartment of the  
detergent drawer.  
Š Put detergent into the machine suitable for the  
programmes and maximum loads indicated in the  
“Programme and consumption table”. When you  
use additional chemicals (stain removers, bleachs  
and etc), reduce the amount of detergent.  
Š Use recommended amount of detergent.  
Laundry remains wet at the end of Excessive foam might have occurred and automatic  
the programme. (*)  
foam absorption system might have been activated  
due to too much detergent usage.  
 
Washing Machine / User’s Manual  
26 / EN  
Problem  
Reason  
Solution  
(*) Machine does not switch to spinning step when the laundry is not evenly distributed in the drum to prevent any damage to the machine  
and to its surrounding environment. Laundry should be rearranged and re-spun.  
(**) Regular drum cleaning is not applied. Clean the drum regularly. See 4.4.2  
CAUTION: If you cannot eliminate the problem although you follow the instructions in this section, consult your dealer or the  
Authorized Service Agent. Never try to repair a nonfunctional product yourself.  
A
 
27 / EN  
Washing Machine / User’s Manual  

Bissell Vacuum Cleaner 67E2 User Manual
Black Decker Saw BDCMTRS User Manual
Bosch Appliances Security Camera F01U002316C User Manual
Boston Acoustics Speaker CS 275 User Manual
Briggs Stratton Automobile Parts 25100 User Manual
Brinly Hardy Lawn Mower Accessory SAT 400 BH User Manual
Bushnell Telescope 78 9440 User Manual
Casio Digital Camera QV 5500SX User Manual
CBM America Network Card DT 4180 User Manual
CH Tech Network Card AM101 User Manual